Battery pack from 18650 cells

How many cells in series (S) and in parallel (P), what voltage, capacity and current you get, and which protection board and charger to use.

How to calculate

Pack layout

10S3P

Cells
30 pcs
Nominal voltage
36 V
Fully charged
42 V
Discharged to
26.5 V
Capacity
10.4 Ah
Energy
373 Wh
Continuous current
up to 24 A
Cells weight
1.44 kg
Protection board (BMS)
Li-ion 10S, 20 A
Charging
42 V, current up to 5.18 A
  • Use cells of one model and one batch. Charge them to the same voltage before assembly: the difference should be no more than 0.05 V.
  • A 10S protection board with balancing: it watches every group and does not let one of them overcharge.
  • Join cells with nickel strip by spot welding. Soldering overheats the cell and damages it from the inside.

With nickel strip, BMS, heat shrink and wires the pack weighs about 10-15 % more than the cells alone. The BMS current is the load current plus a 25 % margin.

3P: 3 cells in parallel, 10.4 Ah10S13.6 V27.2 V310.8 V414.4 V518 V621.6 V725.2 V828.8 V932.4 V1036 V−0 V+36 V10S: 10 groups in series, 36 V
Top view. A row is a group: its cells sit side by side and are connected in parallel, so capacity and current add up. The groups are connected one after another, so voltages add up: the voltage after each group is shown on the right. A solid strip on top, a dashed one at the bottom, a circle in the middle marks the cell plus. The pack plus is at the top of group 10.

S×P layout and the BMS

Cells connected in series (S) add their voltage, in parallel (P) they add capacity and current. The calculator divides the voltage you need by the cell's nominal voltage and rounds to a whole number of S, and takes P as the larger of two calculations: by capacity and by load current. A Li-ion cell is 3.6 V nominal, 4.2 V fully charged, a LiFePO4 cell 3.2 and 3.65 V. The calculator takes the protection board (BMS) current 25 % above the load current and rounds up to a multiple of 5 A.

Examples

  • 36 V at 10 A·h from Samsung 35E (3450 mA·h): 10S3P, 30 cells, 373 W·h and 1.44 kg of cells. At a load current of 15 A the calculator suggests a 10S BMS rated 20 A.
  • 12 V at 12 A·h from LiFePO4 32700 cells of 6000 mA·h: 4S2P, 12.8 V nominal, 14.6 V fully charged.

Common mistakes

  • People connect cells without equalizing their voltage: when connected in parallel, an equalizing current flows between them. The calculator asks for a difference of no more than 0.05 V.
  • People leave the balance connector plugged into the BMS while welding wires to the pack: the Daly instructions require disconnecting it during the work.
  • People pick a BMS with a rating right at the working current of a screwdriver: at start-up and when the chuck jams the motor draws more than its working current, and the protection cuts off the battery.

FAQ

What do 13S4P and 10S3P mean?
13S4P is 13 groups in series, each with 4 cells in parallel, 52 cells in all. With 3000 mA·h 18650 cells such a pack gives 46.8-48.1 V nominal (13 × 3.6-3.7 V), 54.6 V fully charged (13 × 4.2 V) and 12 A·h (4 × 3 A·h). 10S3P is 30 cells: 36 V nominal, 42 V fully charged, 9 A·h from the same cells.
How many 18650 cells do I need for 12, 24, 36 and 48 V?
In series 3, 7, 10 and 13 cells: 3S gives 10.8 V nominal, 7S 25.2 V, 10S 36 V, 13S 46.8 V. The total number of cells is S × P, for example 3S4P is 12 cells and 12 A·h from 3000 mA·h cells.
How do I connect a 3S or 4S BMS?
The thick B− wire goes to the pack's negative, P− to the negative of the load and charger, and the load's positive is taken from the pack's positive. Balance wires: B− to the negative of the first group, B1 to the joint between the first and second groups, B2 to the joint between the second and third, and the last to the pack's positive. The Daly instructions say to connect them starting from B− in ascending order; before that, check with a multimeter that the voltage between adjacent wires is that of one group.
Can I solder 18650 cells with a soldering iron?
The Samsung ICR18650-28A datasheet forbids soldering to the cell's casing: the heat can damage the separator inside. Spot-weld the strip, and solder the wire to the welded strip.
Which BMS should I use for a cordless screwdriver?
A 12 V screwdriver is 3S, an 18 V and a 21 V one is 5S (18 V nominal, 21 V fully charged). Pick the BMS current by the continuous load current: at 20 A the calculator suggests a 25 A board.
Can I build a pack from cells of different capacities, or used ones?
A pack delivers the capacity of the group with the lowest capacity, and the total capacities of the groups must match. Before assembly, used cells are discharged on a charger that measures capacity and sorted into groups with equal sums. The calculator assumes a pack of identical cells.

You might also need