E6, E12, E24, E48, E96 value series
Which resistor and capacitor values are made and which one to take instead of the calculated value. The code on the case is decoded by the marking page.
Nearest value
Looking for 3.3 kΩ.
| Series | Tolerance | Nearest | Deviation | Lower or equal | Higher or equal |
|---|---|---|---|---|---|
| E6 | ±20 % | 3.3 kΩ | exact | 3.3 kΩ | 3.3 kΩ |
| E12 | ±10 % | 3.3 kΩ | exact | 3.3 kΩ | 3.3 kΩ |
| E24 | ±5 % | 3.3 kΩ | exact | 3.3 kΩ | 3.3 kΩ |
| E48 | ±2 % | 3.32 kΩ | +0.61 % | 3.16 kΩ | 3.32 kΩ |
| E96 | ±1 % | 3.32 kΩ | +0.61 % | 3.24 kΩ | 3.32 kΩ |
The nearest value is found by ratio, which is how the series themselves are built. For an LED resistor take the “higher or equal” column: the current comes out slightly below the calculated one.
E6 series, tolerance ±20 %
6 values per decade. Multiply a table value by 10, 100, 1000 and so on: 4.7 gives 47 Ω, 470 Ω and 4.7 kΩ.
- 1.0
- 1.5
- 2.2
- 3.3
- 4.7
- 6.8
E12 series, tolerance ±10 %
12 values per decade. Multiply a table value by 10, 100, 1000 and so on: 4.7 gives 47 Ω, 470 Ω and 4.7 kΩ.
- 1.0
- 1.2
- 1.5
- 1.8
- 2.2
- 2.7
- 3.3
- 3.9
- 4.7
- 5.6
- 6.8
- 8.2
E24 series, tolerance ±5 %
24 values per decade. Multiply a table value by 10, 100, 1000 and so on: 4.7 gives 47 Ω, 470 Ω and 4.7 kΩ.
- 1.0
- 1.1
- 1.2
- 1.3
- 1.5
- 1.6
- 1.8
- 2.0
- 2.2
- 2.4
- 2.7
- 3.0
- 3.3
- 3.6
- 3.9
- 4.3
- 4.7
- 5.1
- 5.6
- 6.2
- 6.8
- 7.5
- 8.2
- 9.1
E48 series, tolerance ±2 %
48 values per decade. Multiply a table value by 10, 100, 1000 and so on: 4.87 gives 48.7 Ω, 487 Ω and 4.87 kΩ.
- 1.00
- 1.05
- 1.10
- 1.15
- 1.21
- 1.27
- 1.33
- 1.40
- 1.47
- 1.54
- 1.62
- 1.69
- 1.78
- 1.87
- 1.96
- 2.05
- 2.15
- 2.26
- 2.37
- 2.49
- 2.61
- 2.74
- 2.87
- 3.01
- 3.16
- 3.32
- 3.48
- 3.65
- 3.83
- 4.02
- 4.22
- 4.42
- 4.64
- 4.87
- 5.11
- 5.36
- 5.62
- 5.90
- 6.19
- 6.49
- 6.81
- 7.15
- 7.50
- 7.87
- 8.25
- 8.66
- 9.09
- 9.53
E96 series, tolerance ±1 %
96 values per decade. Multiply a table value by 10, 100, 1000 and so on: 4.87 gives 48.7 Ω, 487 Ω and 4.87 kΩ.
- 1.00
- 1.02
- 1.05
- 1.07
- 1.10
- 1.13
- 1.15
- 1.18
- 1.21
- 1.24
- 1.27
- 1.30
- 1.33
- 1.37
- 1.40
- 1.43
- 1.47
- 1.50
- 1.54
- 1.58
- 1.62
- 1.65
- 1.69
- 1.74
- 1.78
- 1.82
- 1.87
- 1.91
- 1.96
- 2.00
- 2.05
- 2.10
- 2.15
- 2.21
- 2.26
- 2.32
- 2.37
- 2.43
- 2.49
- 2.55
- 2.61
- 2.67
- 2.74
- 2.80
- 2.87
- 2.94
- 3.01
- 3.09
- 3.16
- 3.24
- 3.32
- 3.40
- 3.48
- 3.57
- 3.65
- 3.74
- 3.83
- 3.92
- 4.02
- 4.12
- 4.22
- 4.32
- 4.42
- 4.53
- 4.64
- 4.75
- 4.87
- 4.99
- 5.11
- 5.23
- 5.36
- 5.49
- 5.62
- 5.76
- 5.90
- 6.04
- 6.19
- 6.34
- 6.49
- 6.65
- 6.81
- 6.98
- 7.15
- 7.32
- 7.50
- 7.68
- 7.87
- 8.06
- 8.25
- 8.45
- 8.66
- 8.87
- 9.09
- 9.31
- 9.53
- 9.76
How the series are built
The En series divides a decade (from 1 to 10) into n values so that each next one is about the same factor larger than the previous: 1.21 times for E12, 1.10 times for E24. The values are rounded to two significant digits for E6-E24 and to three for E48 and E96. That is how the IEC 60063 standard defines it.
The more accurate the resistor, the more values in its series: E6 is made with a 20 % tolerance, E12 with 10 %, E24 5 %, E48 2 %, E96 1 %. The step between adjacent values is about twice the tolerance.
Examples
- The calculation gave 3.1 kΩ. In E24 the nearest is 3 kΩ (−3.2 %), in E96 3.09 kΩ (−0.3 %).
- The LED resistor by the formula is 165 Ω. Take the larger one from E12, 180 Ω: the current will be slightly lower than calculated.
FAQ
- Which series do ordinary through-hole resistors use?
- Through-hole resistors with a 5 % tolerance (four bands) are made in the E24 series, and 1 % metal film resistors (five bands) in E96. Assortment kits from a shop often have only part of E12 or E24.
- Why is there no 5 kΩ resistor?
- 5 kΩ is not in E24: the neighbors are 4.7 and 5.1 kΩ. E96 has 4.99 kΩ. If you need exactly 5 kΩ, connect two 10 kΩ resistors in parallel.
- Which series are capacitors made in?
- Ceramic and film capacitors mostly in E6 and E12 (100 nF, 220 nF, 470 nF), electrolytics in E3 and E6 (10, 22, 47 µF).
You might also need
Part markings
resistor colour bands and SMD codes, capacitor codes, both ways
pF, nF and µF converter
capacitance in picofarads, nanofarads and microfarads and the code on the case
LED resistor
resistance, standard value and resistor power
Voltage divider
output from R1 and R2 or picking a pair from a series, ADC check