Robot calculator

Gears, wheels, a servo for an arm and a motor for a cart: how many revolutions and how much torque you need.

What to calculate

Gear ratio

: 13 : 1

Output speed
1,000 rpm
Output torque
1.42 kg·cm, 0.14 N·m
Efficiency of the whole drive
95 %
  • Fewer than 17 teeth. On spur gears with a 20° pressure angle and no profile shift the root of such a tooth is undercut and weak; bought small gears are made with a shift.

A spur gear pair is 95-98 % efficient, a worm pair 40-80 %. The direction of rotation flips at every pair: with an odd number of stages the output turns the other way. 1 kg·cm = 0.098 N·m.

Servo torque and gear ratio

The calculator works out the torque at an arm joint for the arm stretched out horizontally, as the sum of mass × lever arm. A link's mass is applied at its middle, the next joint's servo at the end of the link, the payload at the end of the arm. The result is multiplied by a margin, 2 by default: the servo's datasheet gives the holding (stall) torque, at which the shaft stops.

Examples

  • A 12-tooth gear on a motor at 3000 rpm and 0.5 kgf·cm drives a 36-tooth gear: gear ratio 36 / 12 = 3, output 1000 rpm and 0.5 × 3 × 0.95 ≈ 1.4 kgf·cm at a pair efficiency of 95 %.
  • An arm with links of 12 and 10 cm weighing 40 and 30 g, a 55 g servo at the elbow and a 100 g payload: the shoulder needs 3.6 kgf·cm, which with a margin of 2 is 7.2 kgf·cm. At 6 V an MG995 (10 kgf·cm) or MG996R (11 kgf·cm) will do.

Common mistakes

  • People calculate the arm from the payload at the end only: an MG996R weighing 55 g at the end of a 12 cm link adds 0.66 kgf·cm to the shoulder.
  • People calculate speed from the motor rpm in the datasheet: it is often the no-load speed, and under load the cart moves slower than calculated.
  • People use a gear with fewer than 17 teeth at a 20° pressure angle without profile shift: the tooth root gets undercut and weakens.

FAQ

What is the torque of an SG90 and an MG996R at 4.8 and 6 V?
According to the TowerPro datasheet an SG90 gives 1.8 kgf·cm (0.18 N·m) at 4.8 V and weighs 9 g; there is no torque for 6 V in the datasheet. An MG996R gives 9.4 kgf·cm (0.92 N·m) at 4.8 V and 11 kgf·cm (1.08 N·m) at 6 V, weighs 55 g, and turns 60° in 0.19 s at 4.8 V and in 0.15 s at 6 V.
Is an SG90 enough for a 15 cm manipulator arm?
If the link weighs 20 g and the payload at the end is 30 g, you need 0.02 kg × 7.5 cm + 0.03 kg × 15 cm = 0.6 kgf·cm, and with a margin of 2 that is 1.2 kgf·cm. An SG90 with 1.8 kgf·cm is enough; with the same margin it will hold about 50 g at the end of such an arm.
How do I convert kgf·cm to N·m?
Multiply by 0.0980665: 1 kgf·cm is the weight of 1 kg on a 1 cm lever at g = 9.80665 m/s². In reverse, 1 N·m ≈ 10.2 kgf·cm. On servos this unit is written as kg·cm.
How do I calculate the gear ratio from tooth counts, and what happens to the torque?
Divide the tooth count of the driven gear by that of the driving gear; with several stages, multiply the ratios. Output speed is divided by the gear ratio, and torque is multiplied by it and by the efficiency of each stage, 95-98 % for a pair of spur gears. Each pair reverses the direction of rotation.
What speed does a 200 rpm motor give with a 65 mm wheel?
v = π × D × n / 60 = 3.14 × 0.065 m × 200 / 60 ≈ 0.68 m/s, which is 2.45 km/h. Under load the motor turns slower than its datasheet rpm.

You might also need