ESP-01S (ESP8266) pinout
ESP-01S (Ai-Thinker), ESP8266EX, 3.3 V logic, 14.4×24.7 mm, 8 pins
verified15.10.2026
Top view (chip side), antenna at the top, header at the bottom, rotated 90° on the diagram.
CompareDownload PNG- Chip
- ESP8266EX
- Logic
- 3.3 V
- Power
- 3V3 3-3.6 V
Which ESP-01S (ESP8266) pins are safe to use
Free to use
GPIO3
Use with care
- GPIO0, GPIO2: strapping: the level at power-up selects the boot mode.
- GPIO1: signal at boot.
Important
- 3.3 V only for supply and signals.
- For flashing: IO0 to ground at power-up (or reset), IO2 and EN to 3.3 V, TX/RX crossed to a USB-UART adapter.
- Labels are printed on the back side (mirrored), none on the front.
- ESP-01S: pull-ups of EN, RST, IO0 to the supply and GPIO15 to ground are already on the board.
- GPIO1 (TX) and GPIO3 (RX) can be used as regular GPIO if you do not need Serial.
- Do not apply 5 V to VCC or the signals. The module does not work from the 3.3 V pin of an Arduino Uno (50 mA).
Revisions and clones
- ESP-01 (old): red power LED and a blue one on TX, no pull-ups on EN and RST, often a blue solder mask.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| GND | pin 1 | Ground | verified | |
| IO2 | GPIO2, pin 2 | interruptPWM (software)UART1 TX (Serial1, transmit only) | not 5 V tolerantaffects boot (strapping)onboard LEDonboard pull-up | verifiedMust be high at reset, otherwise the board will not start.ESP-01S: blue LED on GPIO2, lights at LOW. |
| IO0 | GPIO0, pin 3 | interruptPWM (software) | not 5 V tolerantaffects boot (strapping)onboard pull-up | verifiedAt reset: low = firmware download mode, high is needed for a normal boot. |
| RX | GPIO3, pin 4 | interruptPWM (software)UART0 RX | not 5 V tolerant | verifiedUsed for UART flashing.Square pad.Labelled on other revisions as: RXD |
| TX | GPIO1, pin 5 | interruptPWM (software)UART0 TX | not 5 V tolerantoutputs a signal at boot | verifiedPrints the bootloader log at boot (74880 baud).Labelled on other revisions as: TXD |
| EN | pin 6 | CH_PD: chip enable (high = running) | onboard pull-up | verifiedESP-01S: pull-up to 3.3 V already on the board.Labelled on other revisions as: CH_PD |
| RST | pin 7 | Reset (low = reset) | onboard pull-up | verifiedESP-01S: pull-up to 3.3 V already on the board. |
| 3V3 | pin 8 | 3.3 V | power input | verified3.3 V only. Current peaks during transmission up to ~300 mA: use a regulator with headroom and a 100–470 µF capacitor nearby.Labelled on other revisions as: VCC |
Sources
Every pin is verified against the manufacturer's documents.
- ESP-01S Specification V1.1 (Ai-Thinker)datasheet, checked 15.10.2026size 14.4×24.7 mm, 2×4 header (x 3.5–11.12, rows y 20.66 and 23.2), pin numbers and functions, LEDs, pull-ups, 1 MB flash
- ESP-01/07/12 Series User Manual V1.3 (Ai-Thinker)user guide, checked 15.10.2026the component-side view in the photo matches the drawing; the ESP-01 needs external EN and RST pull-ups, the ESP-01S does not
- ESP8266EX Datasheet (Espressif)datasheet, checked 15.10.2026pins and functions, TOUT (ADC 0–1.0 V), HSPI, UART0/UART1, strapping GPIO0/2/15, flash pins, GPIO16 XPD_DCDC
- ESP8266 Arduino Core: Reference (GPIO, PWM, interrupts, Serial)Arduino core, checked 15.10.2026PWM on GPIO0–16, interrupts on all except GPIO16, GPIO6–11 used by flash, Serial1 TX only on GPIO2, Serial.swap on 15/13
- esp8266/Arduino: variants/nodemcu/pins_arduino.h and common.hArduino core, checked 15.10.2026D0–D8 ↔ GPIO, SDA 4, SCL 5, SS 15, MOSI 13, MISO 12, SCK 14, LED_BUILTIN 2
Size: per the Ai-Thinker drawing (24.6 in the specification text).
FAQ
- Which pin is the ESP-01S (ESP8266) LED on?
- Blue LED on GPIO2, lights at LOW.
- Are the ESP-01S (ESP8266) pins 5 V tolerant?
- No. The logic is 3.3 V and the pins are not 5 V tolerant: use a divider or a level shifter for 5 V signals.
- What supply voltage does the ESP-01S (ESP8266) need?
- 3V3: 3-3.6 V. 3.3 V logic.
You might also need
Schematic with this board
schematic builder with the board already placed
Flash this board
upload a sketch or .bin to this board from the browser
Power budget
will the regulator cope and how long the battery lasts
Calculators
LED resistor, voltage divider, battery runtime, 3D print cost, LED strip power supply and pF, nF, µF conversion



