BME280 GY-BME280 pinout
BME280 GY-BME280 (6 pins, 3.3 V only), Bosch BME280, 3.3 V logic, 15×11 mm, 6 pins
partly verified15.10.2026
Front view (sensor side), connector at the bottom.
Download PNG- Chip
- Bosch BME280
- Logic
- 3.3 V
- Power
- VCC 1.71-3.6 V
- I2C address
- 0x76second 0x77: SDO to VCC
Important
- 3.3 V supply only. I2C from a 5 V board works (pull-ups to 3.3 V), SPI only through a level shifter.
- I2C address 0x76 (SDO to ground) or 0x77 (SDO to 3.3 V).
- A BMP280 (no humidity) is often sold in place of the BME280: check chip_id (0x60 for BME280, 0x58 for BMP280).
- Geometry from independent KiCad footprints and photos (±0.3 mm). Holes and small components are approximate, check with calipers.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| VCC | 3.3 V | power input | not from manufacturerModule with no manufacturer: the order is confirmed by two independent photos/descriptions, coordinates from one footprint.Labelled on other revisions as: VIN | |
| GND | Ground | not from manufacturerModule with no manufacturer: the order is confirmed by two independent photos/descriptions, coordinates from one footprint. | ||
| SCL | I2C SCLSPI SCK | not 5 V tolerantonboard pull-up | not from manufacturerModule with no manufacturer: the order is confirmed by two independent photos/descriptions, coordinates from one footprint.10 kΩ pull-up to 3.3 V on the board: works with a 5 V MCU over I2C without a level shifter (open-drain bus).Labelled on other revisions as: SCK | |
| SDA | I2C SDASPI SDI (MOSI) | not 5 V tolerantonboard pull-up | not from manufacturerModule with no manufacturer: the order is confirmed by two independent photos/descriptions, coordinates from one footprint.Labelled on other revisions as: SDI | |
| CSB | SPI CSinterface select: high or unconnected = I2C | not 5 V tolerantonboard pull-up | not from manufacturerModule with no manufacturer: the order is confirmed by two independent photos/descriptions, coordinates from one footprint.10 kΩ pull-up: I2C by default. Leave unconnected for I2C. | |
| SDO | I2C address: to ground 0x76, to 3.3 V 0x77SPI SDO (MISO) | not 5 V tolerantonboard pull-down | not from manufacturerModule with no manufacturer: the order is confirmed by two independent photos/descriptions, coordinates from one footprint.Weak pull-down to ground: the default address is 0x76. |
Sources
Not verified against the manufacturer: 6 of 6 pins. The pin card says what confirms each one and where sources disagree.
- Bosch BME280 datasheet (BST-BME280-DS002, Rev 1.24)datasheet, checked 15.10.2026VDD 1.71–3.6 V, CSB to VDDIO = I2C, to ground = SPI, SDO selects the address 0x76/0x77, don't hold the interface high without power
- ProtoSupplies: GY-BME280 modulethird-party source, checked 15.10.2026order VCC, GND, SCL, SDA, CSB, SDO; 1.7-3.6 V without a regulator; 10 kΩ pull-ups; default address 0x76; 15.5×11.5 mm
- Random Nerd Tutorials: BME280 with Arduino (photo of the 6-pin board)third-party source, checked 15.10.2026the same order (board photographed with the header up), SCK/SDI labels on CJMCU
- KiCad: mirkosertic/ESP8266Weatherstation «BME280 DIP»third-party source, checked 15.10.2026size 15×11, row and hole positions
Size: from the KiCad footprint; ProtoSupplies lists 15.5×11.5 (approximate).
FAQ
- What is the I2C address of the BME280 GY-BME280?
- 0x76. Tie SDO to VCC and the address becomes 0x77. SDA and SCL pull-ups are on the module.
- What supply voltage does the BME280 GY-BME280 need?
- VCC: 1.71-3.6 V. 3.3 V logic.



