microSD SPI module with regulator and level shifting pinout
microSD SPI module with regulator and level shifting (Catalex, 6 pins), microSD socket, AMS1117-3.3, 74LVC125A, 5 V logic, 41.8×23.75 mm, 6 pins
partly verified17.10.2026
Top view, card socket on the left, header on the right.
BuyDownload PNG- Chip
- microSD socket, AMS1117-3.3, 74LVC125A
- Logic
- 5 V
- Power
- VCC 4.5-5.5 V
Important
- For 5 V boards (Arduino Uno, Nano, Mega): 5 V supply, SPI lines connected directly.
- With ESP32 and other 3.3 V boards power it from 5 V (the board's VIN or 5V): from 3.3 V the AMS1117 regulator will not give the card enough voltage.
- Format the card as FAT32; use the SD or SdFat library.
- Geometry from a single KiCad footprint (±0.3 mm), components drawn approximately.
Revisions and clones
- The large module for a full-size SD with 8 pins (two GND, 3V3, 5V) is a different module.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| CS | SPI CS of the card (SS) | 5 V tolerant | not from manufacturerModule with no manufacturer: order from the labeled footprint and descriptions (they match). The two far holes and small components are not dimensioned. | |
| SCK | SPI SCK | 5 V tolerant | not from manufacturerModule with no manufacturer: order from the labeled footprint and descriptions (they match). The two far holes and small components are not dimensioned. | |
| MOSI | SPI MOSI | 5 V tolerant | not from manufacturerModule with no manufacturer: order from the labeled footprint and descriptions (they match). The two far holes and small components are not dimensioned. | |
| MISO | SPI MISO | not from manufacturerModule with no manufacturer: order from the labeled footprint and descriptions (they match). The two far holes and small components are not dimensioned.3.3 V output: a 5 V Arduino reads it correctly.On these boards MISO does not release the bus even when CS is high: with other SPI devices on the same bus there can be glitches. | ||
| VCC | 5 V | power input | not from manufacturerModule with no manufacturer: order from the labeled footprint and descriptions (they match). The two far holes and small components are not dimensioned. | |
| GND | Ground | not from manufacturerModule with no manufacturer: order from the labeled footprint and descriptions (they match). The two far holes and small components are not dimensioned. |
Sources
Not verified against the manufacturer: 6 of 6 pins. The pin card says what confirms each one and where sources disagree.
- KiCad: maltsevda/TZXDuino_HFHW Catalex_Micro_SD.kicad_modthird-party source, checked 17.10.2026outline 41.8×23.75, header at the right edge: CS, SCK, MOSI, MISO, VCC, GND; two Ø2 holes on the left
- Arduino forum: datasheet for Catalex MicroSD Card Adapterthird-party source, checked 17.10.2026no datasheet; the board has a 3.3 V regulator and a level buffer; MISO is always active
- Components101: Micro SD Card Modulethird-party source, checked 17.10.2026pins GND, VCC, MISO, MOSI, SCK, CS; AMS1117 and 74LVC125A
- TI SN74LVC125A datasheetdatasheet, checked 17.10.2026inputs tolerate up to 5.5 V at a 3.3 V supply
Size: from the KiCad footprint (TZXDuino), sellers list 42×24 (approximate).
FAQ
- What supply voltage does the microSD SPI module with regulator and level shifting need?
- VCC: 4.5-5.5 V. 5 V logic.
