WS2812B strip pinout
WS2812B strip, 5 V, 60 LED/m (one segment), Worldsemi WS2812B, 5 V logic, 16.67×10 mm, 6 pins
partly verified15.10.2026
Top view, data runs left to right (along the arrow), input on the left.
BuyDownload PNG- Chip
- Worldsemi WS2812B
- Logic
- 5 V
- Power
- +5V 3.7-5.3 V
Important
- Why a 60 LED/m strip: it is the most common WS2812B form, with an unambiguous pin set (+5V, DIN, GND at the input and +5V, DO, GND at the output). Rings, sticks and module boards differ in the number and position of pads.
- Data goes only along the arrow: connect to DIN at the start of the strip. Cut along the line through the copper pads between LEDs (every 16.7 mm).
- WS2812B supply: 3.7-5.3 V per the V5 datasheet (3.5-5.3 V in the older version).
- Data from a 3.3 V MCU with a 5 V strip supply is borderline (3.5 V needed): a 74AHCT125 level shifter is more reliable.
- Libraries: FastLED, Adafruit_NeoPixel; RMT on ESP32, PIO on Pico.
- The drawing shows one strip segment; the base color may be white or black, the wires are usually red +5V, white GND, green DATA (not on all strips).
- A meter of strip at full brightness draws up to 3.6 A: power it from a separate 5 V supply, and on long strips feed power from both ends.
- Adafruit: a 500-1000 µF capacitor on the supply at the start of the strip, connect GND first, then +5V, then data.
Revisions and clones
- 30 and 144 LED/m strips: pitch 33.3 and 6.9 mm, same pins.
- WS2812B-Mini, WS2813 (two data wires, BI/DI), SK6812 (RGBW) are similar but differ in pins and protocol.
- Rings and sticks (NeoPixel Ring, Stick) have the 5V/PWR, GND, DIN, DOUT pads in other places.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| +5V | 5 V | power input | not verifiedThe pad order (+5V, DIN, GND from top to bottom) differs between strip makers, pad coordinates are approximate (no drawing). Check the labels and the arrow on the strip.Labelled on other revisions as: 5V, VCC | |
| DIN | WS2812 data (input, 800 kbit/s) | not verifiedThe pad order (+5V, DIN, GND from top to bottom) differs between strip makers, pad coordinates are approximate (no drawing). Check the labels and the arrow on the strip.300-500 Ω resistor in series, close to the strip.Logic high threshold is 0.7·VDD: at 5 V supply that is 3.5 V. It does not always work from 3.3 V MCUs (ESP32, Pico): use a 74AHCT125 level shifter or power the first LED through a diode (≈4.3 V).Labelled on other revisions as: DI, Din, D | ||
| GND | Ground | not verifiedThe pad order (+5V, DIN, GND from top to bottom) differs between strip makers, pad coordinates are approximate (no drawing). Check the labels and the arrow on the strip. | ||
| +5V | 5 V | power output | not verifiedThe pad order (+5V, DIN, GND from top to bottom) differs between strip makers, pad coordinates are approximate (no drawing). Check the labels and the arrow on the strip.Labelled on other revisions as: 5V, VCC | |
| DO | WS2812 data (output to the next segment) | not verifiedThe pad order (+5V, DIN, GND from top to bottom) differs between strip makers, pad coordinates are approximate (no drawing). Check the labels and the arrow on the strip.Labelled on other revisions as: DOUT, Dout | ||
| GND | Ground | not verifiedThe pad order (+5V, DIN, GND from top to bottom) differs between strip makers, pad coordinates are approximate (no drawing). Check the labels and the arrow on the strip. |
Sources
Not verified against the manufacturer: 6 of 6 pins. The pin card says what confirms each one and where sources disagree.
- Worldsemi WS2812B-V5 datasheet (Watterott copy)datasheet, checked 15.10.2026VDD 3.7-5.3 V, 12 mA per channel, 800 kbit/s, package 5.0×5.4×1.57 mm, pins 1 VDD, 2 DOUT, 3 VSS, 4 DIN
- Worldsemi WS2812B datasheet (older version, Adafruit copy)datasheet, checked 15.10.2026VDD 3.5–5.3 V, VIH = 0.7·VDD
- Adafruit NeoPixel Uberguide: best practices and poweringthird-party source, checked 15.10.2026300-500 Ω resistor at the first pixel, 500-1000 µF capacitor, connection order GND → +5V → data, 74AHCT125 for 3.3 V logic, up to 60 mA per pixel
- ShillehTek: WS2812B LED strip 60 LED/m manualthird-party source, checked 15.10.202610 mm strip, 60 LEDs per meter, +5V, DIN, GND pads at the input and DOUT at the output, cut line at each LED, direction arrow
Size: 10 mm wide, 16.67 mm pitch (60 per meter); some strips are actually 12 mm (approximate).
FAQ
- What supply voltage does the WS2812B strip need?
- +5V: 3.7-5.3 V. 5 V logic.



