Arduino Nano V3 pinout
Arduino Nano (ATmega328P), ATmega328P, 5 V logic, 43.18×17.78 mm, 36 pins
partly verified15.10.2026
- D13PB513LEDSPI SCK
- 3V33.3 V
- REFAREF5 V
- A0PC014ADC0
- A1PC115ADC1
- A2PC216ADC2
- A3PC317ADC3
- A4PC418I2C SDAADC4
- A5PC519I2C SCLADC5
- A6ADC620analog
- A7ADC721analog
- 5V5 V
- RSTMCU reset
- GND
- VIN7-12 V
- +5V5 V
- MISOPB4SPI MISO
Top view, USB on the left (as on the official pinout), rotated 90° on the diagram.
BuyCompareDownload PNG- Chip
- ATmega328P
- Logic
- 5 V
- Power
- Mini-USB 4.75-5.25 VVIN 7-12 V5V
- Defaults in Arduino AVR core
- I2C: SDA 18, SCL 19SPI: MOSI 11, MISO 12, SCK 13, SS 10UART: TX 1, RX 0LED: 13
Which Arduino Nano V3 pins are safe to use
Free to use
D0-D12, A0-A5
Use with care
- D13: onboard LED.
- A6, A7: analog input only.
Important
- 5 V logic.
- A6 and A7 are analog inputs only: digitalRead/digitalWrite do not work on them.
- PWM: D3, D5, D6, D9, D10, D11 (marked with an asterisk, not a tilde, on the board).
- D0 (RX0) and D1 (TX1) are used by the USB-UART during flashing and Serial.
- The two RST pins and the two GND pins are tied together.
- The FT232RL chip and the 5 V regulator are on the back side.
Revisions and clones
- CH340G clones: a CH340 bridge instead of the FT232RL, often a 12 MHz crystal for the CH340 on the back; flashing may need "ATmega328P (Old Bootloader)". Same pins.
- Newer clones come with USB-C and micro-USB; LED colors and solder mask differ.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| D12 | PB4, Arduino 12 | SPI MISOPCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| D11 | PB3, Arduino 11 | PWM OC2A (Timer2)SPI MOSIPCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| D10 | PB2, Arduino 10 | PWM OC1B (Timer1)SPI SSPCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| D9 | PB1, Arduino 9 | PWM OC1A (Timer1)PCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| D8 | PB0, Arduino 8 | ICP1 (Timer1 capture)CLKOPCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| D7 | PD7, Arduino 7 | AIN1 (comparator −)PCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| D6 | PD6, Arduino 6 | PWM OC0A (Timer0, ~980 Hz)AIN0 (comparator +)PCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| D5 | PD5, Arduino 5 | PWM OC0B (Timer0, ~980 Hz)T1 (Timer1 counter input)PCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| D4 | PD4, Arduino 4 | T0 (Timer0 counter input)PCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| D3 | PD3, Arduino 3 | PWM OC2B (Timer2)INT1 (attachInterrupt 1)PCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| D2 | PD2, Arduino 2 | INT0 (attachInterrupt 0)PCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| GND | Ground | verified | ||
| RST | MCU reset (low = reset) | verified | ||
| RX0 | PD0, Arduino 0 | UART RX (RXD)PCINT (pin change interrupt) | verifiedConnected to the board's USB-UART through a resistor: keep it free when flashing and using Serial.Current per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| TX1 | PD1, Arduino 1 | UART TX (TXD)PCINT (pin change interrupt) | verifiedConnected to the board's USB-UART through a resistor: keep it free when flashing and using Serial.Current per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| D13 | PB5, Arduino 13 | SPI SCKPCINT (pin change interrupt) | onboard LED | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings).LED L on the board. |
| 3V3 | 3.3 V | power output | not from manufacturerThe 3V3 current limit was not checked against the FTDI datasheet.3.3 V comes from the FT232RL output (3V3OUT): the current is small, tens of mA. On CH340 clones it comes from a separate regulator or from the CH340 as well. | |
| REF | 5 VAREF: ADC reference voltage | power input | verified | |
| A0 | PC0, Arduino A0 (14) | ADC0PCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| A1 | PC1, Arduino A1 (15) | ADC1PCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| A2 | PC2, Arduino A2 (16) | ADC2PCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| A3 | PC3, Arduino A3 (17) | ADC3PCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| A4 | PC4, Arduino A4 (18) | ADC4I2C SDAPCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| A5 | PC5, Arduino A5 (19) | ADC5I2C SCLPCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings). | |
| A6 | ADC6, Arduino A6 (20) | ADC6 | analog input only | verifiedAnalog input only: digitalRead/digitalWrite and pull-up don't work (ATmega328P in TQFP/QFN package only). |
| A7 | ADC7, Arduino A7 (21) | ADC7 | analog input only | verifiedAnalog input only: digitalRead/digitalWrite and pull-up don't work (ATmega328P in TQFP/QFN package only). |
| 5V | 5 V | power inputpower output | verified | |
| RST | MCU reset (low = reset) | verified | ||
| GND | Ground | verified | ||
| VIN | 9 V | power input | verified5 V regulator input: 7–12 V. | |
| MISO | PB4 | SPI MISOPCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings).Same signal as D12. | |
| +5V | 5 V | power inputpower output | verified | |
| SCK | PB5 | SPI SCKPCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings).Same signal as D13. | |
| MOSI | PB3 | PWM OC2A (Timer2)SPI MOSIPCINT (pin change interrupt) | verifiedCurrent per pin: up to 20 mA operating, 40 mA limit, less for the whole port (datasheet, Absolute Maximum Ratings).Same signal as D11. | |
| RESET | MCU reset (low = reset) | verified | ||
| GND | Ground | verified |
Sources
Not verified against the manufacturer: 1 of 36 pins. The pin card says what confirms each one and where sources disagree.
- Arduino Nano 3.0: Eagle files (ArduinoNano30Eagle.zip)board drawing, checked 15.10.2026size 43.18×17.78 mm, pad centers of J1, J2, ICSP, components and holes, silkscreen D2…D13, RX0, TX1, REF, 3V3
- Arduino Nano Datasheet (A000005)datasheet, checked 15.10.2026pin functions, ports, power
- ATmega328P Datasheet (Microchip DS40002061)datasheet, checked 15.10.2026alternate functions of ports B, C, D: OC0A/B, OC1A/B, OC2A/B, INT0/1, PCINT, SPI, TWI, USART, ADC0–7, AIN0/1; ADC6/7 analog only; pin currents
- ArduinoCore-avr: variants/standard/pins_arduino.hArduino core, checked 15.10.2026Arduino numbers ↔ ports, PWM on 3, 5, 6, 9, 10, 11, SS 10, MOSI 11, MISO 12, SCK 13, SDA A4, SCL A5, LED_BUILTIN 13
Size: per the Eagle file (1.7×0.7 inch).
FAQ
- Which Arduino Nano V3 pins are I2C, SPI and UART?
- By default in Arduino AVR core: I2C: SDA A4, SCL A5; SPI: MOSI D11, MISO D12, SCK D13, SS D10; UART: TX D1, RX D0.
- Which pin is the Arduino Nano V3 LED on?
- L LED on D13.
You might also need
Similar boards
Next
Need firmware or a device built on Arduino? I'll build it to order



