Ebyte E01-2G4M27D (nRF24L01) pinout
Ebyte E01-2G4M27D (nRF24L01P, 27 dBm, SMA), nRF24L01P (Nordic), 3.3 V logic, 18×33.4 mm, 12 pins
partly verified15.10.2026
Top view (screen side), connector at the top, SMA at the bottom, rotated 90° on the diagram. 4 more pins are in the table below.
CompareDownload PNG- Chip
- nRF24L01P (Nordic)
- Logic
- 3.3 V
- Power
- VCC 2.5-5.5 V
Important
- Supply 2.5–5.5 V, but signals are 3.3 V only.
- Signals are 3.3 V. Ebyte warns that the module can burn out on 5 V logic (the old Chinese manual v4.5 allowed up to 5 V, the new ones do not). With an Arduino Uno, use a level shifter.
- Same header as the regular nRF24L01: 1 GND, 2 VCC … 8 IRQ, pin 1 at the right edge.
- Power through a filter (ceramic + tantalum), connect the module ground at a single point (Ebyte).
- Do not transmit without an antenna.
- Transmit current 490 mA at 3.3 V and 390 mA at 5 V (27 dBm): needs a strong power source.
Revisions and clones
- E01C-ML01DP5 is a different module on the Si24R1 with the same pinout and size, but 3.3 V logic only and TX 125 mA.
- E01-ML01SP2 / E01-2G4M27SX are SMD versions with a different pin order (1 VCC … 8 GND).
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| GND | pin 1 | Ground | verified | |
| VCC | pin 2 | 3.3 V | power input | verified2.5–5.5 V (Ebyte E01-2G4M27D). Signals are still 3.3 V. |
| CE | pin 3 | CE: enable receive/transmit (active high) | not 5 V tolerant | verifiedEbyte: signal level is 3.3 V, the module can burn out on 5 V logic. Use a level shifter. |
| CSN | pin 4 | SPI CS (CSN, active low) | not 5 V tolerant | verifiedEbyte: signal level is 3.3 V, the module can burn out on 5 V logic. Use a level shifter. |
| SCK | pin 5 | SPI SCK | not 5 V tolerant | verifiedEbyte: signal level is 3.3 V, the module can burn out on 5 V logic. Use a level shifter. |
| MOSI | pin 6 | SPI MOSI (module input) | not 5 V tolerant | verifiedEbyte: signal level is 3.3 V, the module can burn out on 5 V logic. Use a level shifter. |
| MISO | pin 7 | SPI MISO (module output) | verifiedModule output: level equals the module supply (3.3 V). Usually enough for the input of a 5 V MCU. | |
| IRQ | pin 8 | IRQ: interrupt (active low)to the MCU interrupt pin | verifiedCan be left unconnected if you poll the status over SPI. | |
| GND | pin 9 | Ground | verified | |
| GND | pin 10 | Ground | verified | |
| GND | pin 11 | Ground | not verifiedThe position of pins 11 and 12 is not dimensioned in the drawing, taken by symmetry with 9 and 10. | |
| GND | pin 12 | Ground | not verifiedThe position of pins 11 and 12 is not dimensioned in the drawing, taken by symmetry with 9 and 10. |
Sources
Not verified against the manufacturer: 2 of 12 pins. The pin card says what confirms each one and where sources disagree.
- Nordic nRF24L01+ Product Specification v1.0 (SparkFun copy)datasheet, checked 15.10.2026pin functions CE, CSN, SCK, MOSI, MISO, IRQ; VDD 1.9–3.6 V; inputs tolerate 5 V (VIH up to 5.25 V) at VDD 2.7–3.3 V; TX current 11.3 mA at 0 dBm, RX 13.5 mA; supply decoupling
- Ebyte E01-2G4M27D User Manual v1.30 (2024-12-26)datasheet, checked 15.10.2026size 18.0×33.4 mm, 2×4 connector as on the DP5, pins 9–12 GND (9 and 10 dimensioned), supply 2.5–5.5 V, 3.3 V level, TX 490 mA at 3.3 V
- RF24 library: COMMON_ISSUES.mdthird-party source, checked 15.10.202610 µF capacitor at the module supply pins; PA+LNA modules need a strong power source
Size: per the Ebyte drawing, without the SMA connector.
FAQ
- What supply voltage does the Ebyte E01-2G4M27D (nRF24L01) need?
- VCC: 2.5-5.5 V. 3.3 V logic.



