nRF24L01+PA+LNA pinout
nRF24L01+PA+LNA (with SMA antenna), nRF24L01+ (Nordic), 3.3 V logic, 15.5×41 mm, 8 pins
partly verified15.10.2026
Top view, header at the top, SMA connector at the bottom, rotated 90° on the diagram.
CompareDownload PNG- Chip
- nRF24L01+ (Nordic)
- Logic
- 3.3 V
- Power
- VCC 3-3.6 V
Important
- Supply only 1.9–3.6 V. The module burns out on 5 V.
- 10 µF capacitor (electrolytic or tantalum) right at the module VCC and GND pins: without it the link is unstable, especially from the Arduino 3.3 V pin.
- SPI up to 10 MHz, mode 0. CE and CSN can be any GPIO.
- Transmit current up to ~115 mA, receive ~45 mA. Needs a separate 3.3 V regulator and a capacitor at the module.
- Without an antenna the amplified transmitter can be damaged.
- Modules placed close together (under a meter) at full power overload each other: use RF24_PA_LOW for testing.
- Transmit current up to ~115 mA: power from a separate 3.3 V regulator, not from an Arduino pin.
Revisions and clones
- The amplifier chip and its circuit depend on the batch; fakes without an LNA exist.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| GND | pin 1 | Ground | not from manufacturerNo manufacturer documentation: pins 1–8 are in the same order at all sellers, but the connector position and board size were not checked against a drawing (drawn like a normal module). | |
| VCC | pin 2 | 3.3 V | power input | not from manufacturerNo manufacturer documentation: pins 1–8 are in the same order at all sellers, but the connector position and board size were not checked against a drawing (drawn like a normal module).3.0–3.6 V (sellers: 2.7–3.6 V). Do not apply 5 V. |
| CE | pin 3 | CE: enable receive/transmit (active high) | 5 V tolerant | not from manufacturerNo manufacturer documentation: pins 1–8 are in the same order at all sellers, but the connector position and board size were not checked against a drawing (drawn like a normal module).The input tolerates 5 V when the module is powered at 2.7–3.3 V (Nordic). |
| CSN | pin 4 | SPI CS (CSN, active low) | 5 V tolerant | not from manufacturerNo manufacturer documentation: pins 1–8 are in the same order at all sellers, but the connector position and board size were not checked against a drawing (drawn like a normal module).The input tolerates 5 V when the module is powered at 2.7–3.3 V (Nordic). |
| SCK | pin 5 | SPI SCK | 5 V tolerant | not from manufacturerNo manufacturer documentation: pins 1–8 are in the same order at all sellers, but the connector position and board size were not checked against a drawing (drawn like a normal module).The input tolerates 5 V when the module is powered at 2.7–3.3 V (Nordic). |
| MOSI | pin 6 | SPI MOSI (module input) | 5 V tolerant | not from manufacturerNo manufacturer documentation: pins 1–8 are in the same order at all sellers, but the connector position and board size were not checked against a drawing (drawn like a normal module).The input tolerates 5 V when the module is powered at 2.7–3.3 V (Nordic). |
| MISO | pin 7 | SPI MISO (module output) | not from manufacturerNo manufacturer documentation: pins 1–8 are in the same order at all sellers, but the connector position and board size were not checked against a drawing (drawn like a normal module).Module output: level equals the module supply (3.3 V). Usually enough for the input of a 5 V MCU. | |
| IRQ | pin 8 | IRQ: interrupt (active low)to the MCU interrupt pin | not from manufacturerNo manufacturer documentation: pins 1–8 are in the same order at all sellers, but the connector position and board size were not checked against a drawing (drawn like a normal module).Can be left unconnected if you poll the status over SPI. |
Sources
Not verified against the manufacturer: 8 of 8 pins. The pin card says what confirms each one and where sources disagree.
- Nordic nRF24L01+ Product Specification v1.0 (SparkFun copy)datasheet, checked 15.10.2026pin functions CE, CSN, SCK, MOSI, MISO, IRQ; VDD 1.9–3.6 V; inputs tolerate 5 V (VIH up to 5.25 V) at VDD 2.7–3.3 V; TX current 11.3 mA at 0 dBm, RX 13.5 mA; supply decoupling
- ProtoSupplies: nRF24L01+PA+LNA 2.4GHz RF wireless modulethird-party source, checked 15.10.2026pin order 1 GND … 8 IRQ, 3.0–3.6 V supply, TX up to 115 mA, RX 45 mA, size 41×15 mm
- Elecrow wiki: nRF24L01+PA+LNA wireless modulethird-party source, checked 15.10.2026pin order, 2.7–3.6 V supply, PA +20 dB, LNA +10 dB
- RF24 library: COMMON_ISSUES.mdthird-party source, checked 15.10.202610 µF capacitor at the module supply pins; PA+LNA modules need a strong power source
Size: size differs between sellers (41×15, 45.5×16.5, 37.4×16.6 mm) (approximate).
FAQ
- What supply voltage does the nRF24L01+PA+LNA need?
- VCC: 3-3.6 V. 3.3 V logic.



