ESP32 DevKit V1 (30 pin) pinout
ESP32 DOIT DevKit V1, 30 pins, ESP32 (ESP32-D0WDQ6 / D0WD-V3), 3.3 V logic, 28.2×51.8 mm, 30 pins
verified15.10.2026
- ENbuttonCHIP_PU
- VPGPIO36inADC1_CH0RTC_GPIO0SENSOR_VP
- VNGPIO39inADC1_CH3RTC_GPIO3SENSOR_VN
- D34GPIO34inADC1_CH6RTC_GPIO4
- D35GPIO35inADC1_CH7RTC_GPIO5
- D32GPIO32ADC1_CH4TOUCH9RTC_GPIO9XTAL_32K_P
- D33GPIO33ADC1_CH5TOUCH8RTC_GPIO8XTAL_32K_N
- D25GPIO25ADC2_CH8DAC1RTC_GPIO6
- D26GPIO26ADC2_CH9DAC2RTC_GPIO7
- D27GPIO27ADC2_CH7TOUCH7RTC_GPIO17
- D14GPIO14HSPI SCKADC2_CH6TOUCH6RTC_GPIO16JTAG MTMS
- D12GPIO12BOOTHSPI MISOADC2_CH5TOUCH5RTC_GPIO15JTAG MTDI
- D13GPIO13HSPI MOSIADC2_CH4TOUCH4RTC_GPIO14JTAG MTCK
- GND
- VIN5 V
- D23GPIO23VSPI MOSI
- D22GPIO22I2C SCL
- TX0GPIO1BOOTUART0 TX
- RX0GPIO3UART0 RX
- D21GPIO21I2C SDA
- D19GPIO19VSPI MISO
- D18GPIO18VSPI SCK
- D5GPIO5BOOTVSPI CS
- TX2GPIO17UART2 TX
- RX2GPIO16UART2 RX
- D4GPIO4ADC2_CH0TOUCH0RTC_GPIO10
- D2GPIO2BOOTLEDADC2_CH2TOUCH2RTC_GPIO12
- D15GPIO15BOOTHSPI CSADC2_CH3TOUCH3RTC_GPIO13JTAG MTDO
- GND
- 3V33.3 V
Top view, USB at the bottom, module antenna at the top.
CompareDownload PNG- Chip
- ESP32 (ESP32-D0WDQ6 / D0WD-V3), ESP-WROOM-32 / ESP32-WROOM-32
- Logic
- 3.3 V
- Power
- Micro-USB 4.75-5.25 VVIN 4.5-12 V3V3 3-3.6 V
- Defaults in arduino-esp32 (DOIT ESP32 DEVKIT V1)
- I2C: SDA 21, SCL 22SPI: MOSI 23, MISO 19, SCK 18, SS 5UART: TX 1, RX 3LED: 2
Which ESP32 DevKit V1 (30 pin) pins are safe to use
Free to use
GPIO3, GPIO4, GPIO13, GPIO14, GPIO16-19, GPIO21-23, GPIO25-27, GPIO32, GPIO33
Use with care
- GPIO1: signal at boot.
- GPIO2, GPIO5, GPIO12, GPIO15: strapping: the level at power-up selects the boot mode.
- GPIO34-36, GPIO39: input only, no output and no pull-ups.
Important
- 3.3 V logic, don't put 5 V on the GPIO.
- GPIO0 and the flash pins (GPIO6–11) are not broken out to the header. GPIO0 is only on the BOOT button.
- D34, D35, VP, VN are input only.
- Strapping pins on the header: D2, D5, D12, D15. Keep D12 low at power-up, otherwise the board will not start.
- ADC2 (D2, D4, D12–D15, D25–D27) does not work while Wi-Fi is on.
- Rows 25.4 mm (1 inch) apart, like the DevKitC: almost no free holes are left on a breadboard.
- There is no official documentation for the board: nets from the DOIT schematic, geometry from the full-scale drawing and measurements.
Revisions and clones
- Clones use a CH340C instead of the CP2102 and an AMS1117 instead of the NCP1117; the pins are the same.
- Reports mention narrow clones with rows 0.9 inch apart, whose dimensions were not found. Measure before buying a breadboard.
- There is a 36-pin variant (with GPIO0 and the flash pins), which is a different board.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| EN | CHIP_PU: enable and reset (low = reset) | onboard pull-uponboard button | verifiedEN button on the board: reset. | |
| VP | GPIO36 | interruptADC1_CH0RTC_GPIO0SENSOR_VP | input onlynot 5 V tolerant | verifiedInput only: no output and no internal pull-ups. |
| VN | GPIO39 | interruptADC1_CH3RTC_GPIO3SENSOR_VN | input onlynot 5 V tolerant | verifiedInput only: no output and no internal pull-ups. |
| D34 | GPIO34 | interruptADC1_CH6RTC_GPIO4 | input onlynot 5 V tolerant | verifiedInput only: no output and no internal pull-ups. |
| D35 | GPIO35 | interruptADC1_CH7RTC_GPIO5 | input onlynot 5 V tolerant | verifiedInput only: no output and no internal pull-ups. |
| D32 | GPIO32 | interruptPWM (LEDC)ADC1_CH4TOUCH9RTC_GPIO9XTAL_32K_P (32 kHz crystal) | not 5 V tolerant | verified |
| D33 | GPIO33 | interruptPWM (LEDC)ADC1_CH5TOUCH8RTC_GPIO8XTAL_32K_N (32 kHz crystal) | not 5 V tolerant | verified |
| D25 | GPIO25 | interruptPWM (LEDC)ADC2_CH8RTC_GPIO6DAC1 | ADC2 doesn't work with Wi-Fi onnot 5 V tolerant | verifiedADC2: while Wi-Fi is running, analogRead on this pin doesn't work. For ADC with Wi-Fi, use ADC1 (GPIO32–39). |
| D26 | GPIO26 | interruptPWM (LEDC)ADC2_CH9RTC_GPIO7DAC2 | ADC2 doesn't work with Wi-Fi onnot 5 V tolerant | verifiedADC2: while Wi-Fi is running, analogRead on this pin doesn't work. For ADC with Wi-Fi, use ADC1 (GPIO32–39). |
| D27 | GPIO27 | interruptPWM (LEDC)ADC2_CH7TOUCH7RTC_GPIO17 | ADC2 doesn't work with Wi-Fi onnot 5 V tolerant | verifiedADC2: while Wi-Fi is running, analogRead on this pin doesn't work. For ADC with Wi-Fi, use ADC1 (GPIO32–39). |
| D14 | GPIO14 | interruptPWM (LEDC)ADC2_CH6TOUCH6RTC_GPIO16HSPI SCKJTAG MTMS | ADC2 doesn't work with Wi-Fi onnot 5 V tolerant | verifiedADC2: while Wi-Fi is running, analogRead on this pin doesn't work. For ADC with Wi-Fi, use ADC1 (GPIO32–39). |
| D12 | GPIO12 | interruptPWM (LEDC)ADC2_CH5TOUCH5RTC_GPIO15HSPI MISOJTAG MTDI | affects boot (strapping)ADC2 doesn't work with Wi-Fi onnot 5 V tolerant | verifiedMTDI: selects the flash voltage at reset. High = 1.8 V, so a module with 3.3 V flash won't boot. Internal pull-down.ADC2: while Wi-Fi is running, analogRead on this pin doesn't work. For ADC with Wi-Fi, use ADC1 (GPIO32–39). |
| D13 | GPIO13 | interruptPWM (LEDC)ADC2_CH4TOUCH4RTC_GPIO14HSPI MOSIJTAG MTCK | ADC2 doesn't work with Wi-Fi onnot 5 V tolerant | verifiedADC2: while Wi-Fi is running, analogRead on this pin doesn't work. For ADC with Wi-Fi, use ADC1 (GPIO32–39). |
| GND | Ground | verified | ||
| VIN | 5 V | power inputpower output | verified3.3 V regulator input. Powered from USB it is ~5 V here (after the diode). | |
| D23 | GPIO23 | interruptPWM (LEDC)VSPI MOSI | not 5 V tolerant | verified |
| D22 | GPIO22 | interruptPWM (LEDC)I2C SCL | not 5 V tolerant | verified |
| TX0 | GPIO1 | interruptPWM (LEDC)UART0 TX | outputs a signal at bootnot 5 V tolerant | verifiedPrints the bootloader log at boot (115200 baud).Wired to the USB-UART bridge: busy during flashing and Serial. |
| RX0 | GPIO3 | interruptPWM (LEDC)UART0 RX | not 5 V tolerant | verifiedWired to the USB-UART bridge: busy during flashing and Serial. |
| D21 | GPIO21 | interruptPWM (LEDC)I2C SDA | not 5 V tolerant | verified |
| D19 | GPIO19 | interruptPWM (LEDC)VSPI MISO | not 5 V tolerant | verified |
| D18 | GPIO18 | interruptPWM (LEDC)VSPI SCK | not 5 V tolerant | verified |
| D5 | GPIO5 | interruptPWM (LEDC)VSPI CS (SS) | affects boot (strapping)not 5 V tolerant | verifiedStrapping: SDIO slave timing. Internal pull-up, don't pull it low during reset. |
| TX2 | GPIO17 | interruptPWM (LEDC)UART2 TX | not 5 V tolerant | verified |
| RX2 | GPIO16 | interruptPWM (LEDC)UART2 RX | not 5 V tolerant | verified |
| D4 | GPIO4 | interruptPWM (LEDC)ADC2_CH0TOUCH0RTC_GPIO10 | ADC2 doesn't work with Wi-Fi onnot 5 V tolerant | verifiedADC2: while Wi-Fi is running, analogRead on this pin doesn't work. For ADC with Wi-Fi, use ADC1 (GPIO32–39). |
| D2 | GPIO2 | interruptPWM (LEDC)ADC2_CH2TOUCH2RTC_GPIO12 | affects boot (strapping)ADC2 doesn't work with Wi-Fi onnot 5 V tolerantonboard LED | verifiedAt reset it must be low or floating for download mode. Internal pull-down.ADC2: while Wi-Fi is running, analogRead on this pin doesn't work. For ADC with Wi-Fi, use ADC1 (GPIO32–39).Blue LED on the board through 1 kΩ to ground: lit at a high level. LED_BUILTIN = 2. |
| D15 | GPIO15 | interruptPWM (LEDC)ADC2_CH3TOUCH3RTC_GPIO13HSPI CSJTAG MTDO | affects boot (strapping)ADC2 doesn't work with Wi-Fi onnot 5 V tolerant | verifiedMTDO: low at reset silences the bootloader log on UART0. Internal pull-up.ADC2: while Wi-Fi is running, analogRead on this pin doesn't work. For ADC with Wi-Fi, use ADC1 (GPIO32–39). |
| GND | Ground | verified | ||
| 3V3 | 3.3 V | power inputpower output | verified |
Sources
Every pin is verified against the manufacturer's documents.
- DOIT ESP32 DevKit V1: DOIT schematic (2014-04-13, copy at mischianti)schematic, checked 15.10.2026nets of both rows: Dn = GPIOn, VP 36, VN 39, TX0 1, RX0 3, TX2 17, RX2 16; CP2102, NCP1117, blue LED on GPIO2 to ground
- arduino-esp32: variants/doitESP32devkitV1/pins_arduino.hArduino core, checked 15.10.2026LED_BUILTIN 2, TX 1, RX 3, SDA 21, SCL 22, SS 5, MOSI 23, MISO 19, SCK 18
- Mischianti: DOIT ESP32 DevKit v1, full-scale drawing (SVG)third-party source, checked 15.10.2026size 28.2×51.8 mm, rows 25.4 mm apart, positions of pins, module, buttons and holes, silkscreen labels
- Wokwi: esp32-devkit-v1-elementthird-party source, checked 15.10.2026labels and pin order, rows 25.4 mm apart
- Fritzing forum: DOIT ESP32 DevKit V1 (board measurement)third-party source, checked 15.10.2026measured 28.2×51.8 mm, rows 1 inch apart
- ESP32 Series Datasheet (Espressif)datasheet, checked 15.10.2026IO MUX and pin functions, ADC1/ADC2, touch, DAC, RTC GPIO, strapping (GPIO0, 2, 5, 12, 15), flash pins GPIO6–11, input-only GPIO34–39
- ESP-IDF: GPIO & RTC GPIO (ESP32)user guide, checked 15.10.2026GPIO6–11 used by flash, GPIO34–39 input only with no pull-ups, strapping pins, GPIO1/3 UART0
- ESP-IDF: ADC Oneshot Mode Driver (ESP32)user guide, checked 15.10.2026ADC2 can't be used while Wi-Fi is running
- arduino-esp32: variants/esp32/pins_arduino.hArduino core, checked 15.10.2026defaults: TX 1, RX 3, SDA 21, SCL 22, SS 5, MOSI 23, MISO 19, SCK 18
Size: from a full-scale drawing (mischianti) and measurement; ±0.3 mm on clones (approximate).
FAQ
- Which ESP32 DevKit V1 (30 pin) pins are I2C, SPI and UART?
- By default in arduino-esp32 (DOIT ESP32 DEVKIT V1): I2C: SDA GPIO21, SCL GPIO22; SPI: MOSI GPIO23, MISO GPIO19, SCK GPIO18, SS GPIO5; UART: TX GPIO1, RX GPIO3.
- Which pin is the ESP32 DevKit V1 (30 pin) LED on?
- Blue LED on GPIO2 (lit at HIGH).
- Are the ESP32 DevKit V1 (30 pin) pins 5 V tolerant?
- No. The logic is 3.3 V and the pins are not 5 V tolerant: use a divider or a level shifter for 5 V signals.
- Does ADC2 on the ESP32 DevKit V1 (30 pin) work with Wi-Fi on?
- No. ADC2 pins (GPIO2, GPIO4, GPIO12-15, GPIO25-27) can't read analog while Wi-Fi is on. With Wi-Fi, use GPIO32-36, GPIO39 for the ADC.
You might also need
Similar boards
Next
- Emotion keychainmy ESP32 project, prototype
- ESP32 music playermy ESP32 project, prototype
- DITHR//CAMmy ESP32 project, prototype
Need firmware or a device built on ESP32? I'll build it to order



