Bluetooth HC-05 (ZS-040) pinout
Bluetooth HC-05 on a ZS-040 carrier (6 pins), CSR BC417 (Bluetooth 2.0 SPP), 3.3 V logic, 16.51×36.83 mm, 6 pins
partly verified15.10.2026
Top view (module side), antenna at the top, connector at the bottom.
CompareDownload PNG- Chip
- CSR BC417 (Bluetooth 2.0 SPP)
- Logic
- 3.3 V
- Power
- VCC 3.6-6 V
Important
- 3.6–6 V supply (Components101 says 4–6 V), 3.3 V logic: RXD from a 5 V MCU only through a divider.
- Default speed is 9600 baud, 38400 in AT mode.
- Labels are printed on the back of the carrier.
- Geometry from independent KiCad footprints and photos (±0.3 mm). Holes and small components are approximate, check with calipers.
Revisions and clones
- Older carriers: KEY instead of EN.
- HC-06 on the same carrier: 4 pins (no STATE and EN), no button, slave only.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| STATE | STATE: high when connected | not from manufacturerNo-brand module: pin order follows Martyn Currey's photos and the SPECTRE footprint (they match). | ||
| RXD | Module UART RX (the MCU TX goes here) | not 5 V tolerant | not from manufacturerNo-brand module: pin order follows Martyn Currey's photos and the SPECTRE footprint (they match).3.3 V input: from a 5 V Arduino through a divider (for example 1 kΩ / 2 kΩ). | |
| TXD | Module UART TX (the MCU RX goes here) | not from manufacturerNo-brand module: pin order follows Martyn Currey's photos and the SPECTRE footprint (they match).3.3 V output: a 5 V Arduino reads it fine. | ||
| GND | Ground | not from manufacturerNo-brand module: pin order follows Martyn Currey's photos and the SPECTRE footprint (they match). | ||
| VCC | 5 V | power input | not from manufacturerNo-brand module: pin order follows Martyn Currey's photos and the SPECTRE footprint (they match).Labelled on other revisions as: +5V | |
| EN | EN / KEY: AT mode or shutdown (depends on the carrier) | not verifiedThe EN function differs between carriers: high enables AT mode (ProtoSupplies), low shuts the module off (elektroda), on some boards it is not connected (Martyn Currey). For AT mode it is more reliable to hold the button at power-on.Labelled on other revisions as: KEY |
Sources
Not verified against the manufacturer: 6 of 6 pins. The pin card says what confirms each one and where sources disagree.
- Martyn Currey: HC-05 and HC-06 zs-040 Bluetooth modules, first lookthird-party source, checked 15.10.2026order STATE, RXD, TXD, GND, VCC, EN; labels on the back; button, LED, regulator
- Martyn Currey: HC-05 AT modethird-party source, checked 15.10.2026button → pin 34, enters AT mode, divider on RXD
- ProtoSupplies: HC-05 ZS-040third-party source, checked 15.10.202637×16 mm, 3.6–6 V supply, 3.3 V logic, EN high = AT
- KiCad: Tjeerdie/SPECTRE WIRELESS-BLUETOOTH-HC-05third-party source, checked 15.10.2026size 16.51×36.83, row 1.27 mm from the edge in the center
Size: per the KiCad footprint (SPECTRE); sellers say 37×16 (approximate).
FAQ
- What supply voltage does the Bluetooth HC-05 (ZS-040) need?
- VCC: 3.6-6 V. 3.3 V logic.



