HT7333 regulator pinout
HT7333 regulator (3.3 V, 250 mA, TO-92), HT7333, 3.3 V logic, 7.2×11.5 mm, 3 pins
partly verified17.10.2026
View of the flat marked side, pins down: 1 on the left.
Download PNG- Chip
- HT7333
- Logic
- 3.3 V
- Power
- VIN (pin 2) 3.4-12 V
Important
- Good from a single Li-ion/LiPo cell: dropout about 0.1 V, quiescent current 3.5 µA (for ESP sleep).
- 250 mA is borderline for an ESP32 and ESP8266 with Wi-Fi (peaks of 300–400 mA): put 470 µF on the output, otherwise the board resets during transmission. For more headroom the MCP1700 is no better (250 mA), use an ME6211/RT9080 (500–600 mA) or a switching regulator.
- Holtek is discontinuing the HT73xx series (notice on the site, 2026): clones are on sale, with worse parameters.
- Power dissipation up to 0.5 W: from 5 V at 250 mA it is already 0.43 W, from 12 V about 50 mA is allowed.
Revisions and clones
- SOT-89 (HT7333-A): the same 1 GND, 2 VIN, 3 VOUT, the middle pin and the tab are VIN.
- HT7350 (5 V), HT7330 (3.0 V): same pinout, different output.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| GND | pin 1 | Ground | not from manufacturerThe current Holtek datasheet has only SOT-89 (1 GND, 2 VIN, 3 VOUT); the TO-92 order is from Components101 and older revisions, the same. TO-92 clones may have a different order: check with a multimeter (VIN and GND must not ring to VOUT).Labelled on other revisions as: 1 | |
| VIN | pin 2 | 3.7 V | power input | not from manufacturerThe current Holtek datasheet has only SOT-89 (1 GND, 2 VIN, 3 VOUT); the TO-92 order is from Components101 and older revisions, the same. TO-92 clones may have a different order: check with a multimeter (VIN and GND must not ring to VOUT).Input 3.4–12 V. A 10 µF capacitor at the pin.Labelled on other revisions as: IN, 2 |
| VOUT | pin 3 | 3.3 V | power output | not from manufacturerThe current Holtek datasheet has only SOT-89 (1 GND, 2 VIN, 3 VOUT); the TO-92 order is from Components101 and older revisions, the same. TO-92 clones may have a different order: check with a multimeter (VIN and GND must not ring to VOUT).3.3 V output, up to 250 mA. A 10 µF capacitor at the pin (for an ESP, 100–470 µF for Wi-Fi peaks).Labelled on other revisions as: OUT, 3 |
Sources
Not verified against the manufacturer: 3 of 3 pins. The pin card says what confirms each one and where sources disagree.
- Holtek HT73xx Series Low Power Consumption LDO (Rev. 1.80, 2019)datasheet, checked 17.10.2026SOT-89: 1 GND, 2 VIN, 3 VOUT; 250 mA, input up to 12 V (abs. 14 V), quiescent current 3.5 µA, dissipation 500 mW; this revision has no TO-92
- Components101: HT7333 linear voltage regulator pinout (TO-92)third-party source, checked 17.10.2026TO-92: 1 GND, 2 Vin, 3 Vout
Size: TO-92 package 4.8×4.6 mm, pins spread to 2.54 (approximate).



