OLED 1,3 SH1106 pinout
OLED display 1.3" 128×64 SH1106, I2C (4 pins), Sino Wealth SH1106, 3.3 V logic, 35.4×33.5 mm, 4 pins
partly verified17.10.2026
Front view (screen side), header at the top.
BuyDownload PNG- Chip
- Sino Wealth SH1106
- Logic
- 3.3 V
- Power
- VDD 3.3-5 V
- I2C address
- 0x3Csecond 0x3D
Important
- The pin order on 1.3″ modules varies: check the labels on the board, swapped GND and VDD burn out the module.
- The controller is the SH1106, not the SSD1306: in U8g2 use U8G2_SH1106_128X64_NONAME, in Adafruit use Adafruit_SH110X. With the SSD1306 driver the picture is shifted by 2 pixels with garbage at the edge.
- Address 0x3C (0x3D by re-soldering a resistor on the back).
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| GND | Ground | not verifiedOn 1.3″ modules from different sellers the order differs: GND-VDD-SCK-SDA, VDD-GND-SCK-SDA and VCC-GND-SDA-SCL. Check the labels on your board. | ||
| VDD | 3.3 V | power input | not verifiedOn 1.3″ modules from different sellers the order differs: GND-VDD-SCK-SDA, VDD-GND-SCK-SDA and VCC-GND-SDA-SCL. Check the labels on your board.Labelled on other revisions as: VCC | |
| SCK | I2C SCL | not verifiedOn 1.3″ modules from different sellers the order differs: GND-VDD-SCK-SDA, VDD-GND-SCK-SDA and VCC-GND-SDA-SCL. Check the labels on your board.This is the I2C bus SCL. Pull-up to 3.3 V on the module.Labelled on other revisions as: SCL | ||
| SDA | I2C SDA | not verifiedOn 1.3″ modules from different sellers the order differs: GND-VDD-SCK-SDA, VDD-GND-SCK-SDA and VCC-GND-SDA-SCL. Check the labels on your board. |
Sources
Not verified against the manufacturer: 4 of 4 pins. The pin card says what confirms each one and where sources disagree.
- Sino Wealth SH1106 OLED driver datasheet (Pololu copy)datasheet, checked 17.10.2026I2C address 011110 + SA0 (0x3C/0x3D), memory 132×64, logic supply 1.65-3.5 V
- Robu: 1.3" SH1106 OLED module, pinoutthird-party source, checked 17.10.2026order GND, VDD, SCK, SDA
- Flux: SH1106 1.3 inch I2C OLED modulethird-party source, checked 17.10.20264 pins GND, VDD, SCL, SDA
Size: about 35.4×33.5 mm; header position from photos (approximate).
FAQ
- What is the I2C address of the OLED 1,3 SH1106?
- 0x3C. The second address is 0x3D: resolder the address resistor on the back. SDA and SCL pull-ups are on the module.
- What supply voltage does the OLED 1,3 SH1106 need?
- VDD: 3.3-5 V. 3.3 V logic.



