OLED SSD1306 0,96 pinout
OLED 0,96" 128×64 I2C SSD1306 (GND, VCC, SCL, SDA), SSD1306, 3.3 V logic, 27.3×27.8 mm, 4 pins
partly verified15.10.2026
Front view (display side), connector at the top.
BuyDownload PNG- Chip
- SSD1306
- Logic
- 3.3 V
- Power
- VCC 3.3-5 V
- I2C address
- 0x3Csecond 0x3D
Important
- Read the labels at the connector before connecting: GND and VCC are swapped on different batches. Getting it wrong can burn the display.
- I2C address 0x3C (the board says 0x78, which is the 8-bit form); 0x3D (0x7A) by resoldering the resistor on the back.
- Supply 3.3–5 V. Libraries: Adafruit_SSD1306, U8g2.
- Geometry from independent KiCad footprints and photos (±0.3 mm). Holes and small components are approximate, check with calipers.
Revisions and clones
- Colors: white, blue, yellow-blue (top 16 rows yellow).
- There are 7-pin SPI versions, which are a different module.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| GND | Ground | not from manufacturerUnbranded module: the order GND, VCC, SCL, SDA is the most common, but some boards have VCC first. Check the labels on the board. | ||
| VCC | 5 V | power input | not from manufacturerUnbranded module: the order GND, VCC, SCL, SDA is the most common, but some boards have VCC first. Check the labels on the board. | |
| SCL | I2C SCL | not from manufacturerUnbranded module: the order GND, VCC, SCL, SDA is the most common, but some boards have VCC first. Check the labels on the board.4.7 kΩ pull-up on the board; which supply rail it goes to (3.3 V or VCC) is not verified. Usually works directly with 5 V boards. | ||
| SDA | I2C SDA | not from manufacturerUnbranded module: the order GND, VCC, SCL, SDA is the most common, but some boards have VCC first. Check the labels on the board.4.7 kΩ pull-up on the board; which supply rail it goes to (3.3 V or VCC) is not verified. Usually works directly with 5 V boards. |
Sources
Not verified against the manufacturer: 4 of 4 pins. The pin card says what confirms each one and where sources disagree.
- Solomon Systech SSD1306 datasheet (Adafruit copy)datasheet, checked 15.10.2026I2C address 0b011110+SA0 (0x3C/0x3D), up to 400 kHz, VDD 1.65–3.3 V, panel charge pump
- LastMinuteEngineers: OLED display Arduino tutorialthird-party source, checked 15.10.2026pin order GND, VCC, SCL, SDA, connector at the top
- Arduino forum: 0.96 I2C OLED power inputsthird-party source, checked 15.10.2026both orders exist: GND-VCC and VCC-GND
- TinyTronics: 0.96 inch OLED 128×64 white I2Cthird-party source, checked 15.10.2026supply 3.3–5 V, 4.7 kΩ pull-ups, holes Ø2, address changed by a resistor
- KiCad: CCHS-Melbourne Swag-Badge and neubauek SSD1306_0.96_I2Cthird-party source, checked 15.10.2026size 27.3×27.8, row 1.5 mm from the top at the center
Size: per the KiCad footprint (CCHS); sellers list 27×27…28×28 (approximate).
FAQ
- What is the I2C address of the OLED SSD1306 0,96?
- 0x3C. The second address is 0x3D: resolder the address resistor on the back. SDA and SCL pull-ups are on the module.
- What supply voltage does the OLED SSD1306 0,96 need?
- VCC: 3.3-5 V. 3.3 V logic.



