VL53L0X (GY-VL53L0XV2) pinout
VL53L0X laser distance sensor GY-VL53L0XV2 (6 pins), ST VL53L0X, 3.3 V logic, 25×10.7 mm, 6 pins
partly verified17.10.2026
Top view (sensor side), connector at the bottom.
Download PNG- Chip
- ST VL53L0X
- Logic
- 3.3 V
- Power
- VIN 2.6-5.5 V
- I2C address
- 0x29second 0x30
Important
- I2C address 0x29, the same on all of them: power two or more sensors on one bus one at a time via XSHUT and change the address in software.
- Libraries: Adafruit_VL53L0X, Pololu VL53L0X.
- Remove the protective film from the sensor; glass or dust reduce the range.
- Geometry from KiCad footprints and photos (±0.5 mm). Holes and small components are approximate, check with calipers.
Revisions and clones
- GY-530: a small 10.5×13.3 board with pins on two sides, a different module.
- Pololu 2490 and Adafruit 3317: their own layouts and labels (VDD, VIN, GND, SDA, SCL, XSHUT, GPIO1).
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| VIN | 5 V | power input | not from manufacturerModule with no manufacturer: pin order per the seller's description (VCC/VIN, GND, SCL, SDA, GPIO1, XSHUT), size and connector position are not dimensioned.Labelled on other revisions as: VCC | |
| GND | Ground | not from manufacturerModule with no manufacturer: pin order per the seller's description (VCC/VIN, GND, SCL, SDA, GPIO1, XSHUT), size and connector position are not dimensioned. | ||
| SCL | I2C SCL | onboard pull-up | not from manufacturerModule with no manufacturer: pin order per the seller's description (VCC/VIN, GND, SCL, SDA, GPIO1, XSHUT), size and connector position are not dimensioned.Pull-ups are on the board; their voltage and whether there is a level shifter have not been verified. | |
| SDA | I2C SDA | onboard pull-up | not from manufacturerModule with no manufacturer: pin order per the seller's description (VCC/VIN, GND, SCL, SDA, GPIO1, XSHUT), size and connector position are not dimensioned. | |
| GPIO1 | GPIO1: "measurement ready" interrupt (open drain) | not from manufacturerModule with no manufacturer: pin order per the seller's description (VCC/VIN, GND, SCL, SDA, GPIO1, XSHUT), size and connector position are not dimensioned.ST recommends a 10 kΩ pull-up; not used, leave unconnected. | ||
| XSHUT | Shutdown: low puts the sensor to sleep (5 µA), high or unconnected means it runs | not from manufacturerModule with no manufacturer: pin order per the seller's description (VCC/VIN, GND, SCL, SDA, GPIO1, XSHUT), size and connector position are not dimensioned.Changing the address: all sensors have 0x29. Hold the others in XSHUT = 0, power up one and give it a new address (setAddress), then the next. The address is not kept after power-off.Pulled up on the board; it does not go through the level shifter: with a 5 V Arduino pull it low, do not drive it with 5 V. |
Sources
Not verified against the manufacturer: 6 of 6 pins. The pin card says what confirms each one and where sources disagree.
- ST VL53L0X datasheet (Pololu copy)datasheet, checked 17.10.20262.6-3.5 V supply, I2C up to 400 kHz, address 0x52 (8-bit) = 0x29, XSHUT for hardware sleep 3-7 µA, average current 19 mA, up to 40 mA peak, 10 kΩ pull-ups on XSHUT and GPIO1
- ShillehTek: GY-VL53L0XV2 module manualthird-party source, checked 17.10.20266 pins VCC, GND, SCL, SDA, GPIO1, XSHUT; 2.6-5.5 V; 2.8 V regulator; I2C pull-ups on the board; about 25×11 mm
- Pololu: VL53L0X carrier (2490), for comparisonthird-party source, checked 17.10.2026board with a different layout: level shifting on SDA and SCL, XSHUT without level shifting
Size: sellers list 25×10.7-11 and 25×13; not dimensioned (approximate).
FAQ
- What is the I2C address of the VL53L0X (GY-VL53L0XV2)?
- 0x29. The second address is 0x30: power the sensors one at a time via XSHUT and give this one a new address with setAddress. SDA and SCL pull-ups are on the module.
- What supply voltage does the VL53L0X (GY-VL53L0XV2) need?
- VIN: 2.6-5.5 V. 3.3 V logic.



