Adafruit Micro-Lipo USB-C LiPo charger pinout
Adafruit Micro-Lipo USB-C LiPo charger (MCP73831, product 4410), MCP73831T-2ACI/OT, 5 V logic, 22.86×19.05 mm, 7 pins
verified17.10.2026
Top view, USB-C on the left, JST on the right, row of pins on top.
Download PNG- Chip
- MCP73831T-2ACI/OT
- Logic
- 5 V
- Power
- USB-C 4.5-5.5 V5V 3.75-6 V
Important
- Charge only: there is no over-discharge protection on the board, so connect the load to a battery with protection (Adafruit LiPo cells have it built in).
- A load on BAT during charging disrupts charge termination: the MCP73831 waits for the current to drop below 1/10 of the set value.
- Charge current no more than the battery capacity: 100 mA for 100–500 mAh, 500 mA from 500 mAh.
- Charge current 100 mA (R_PROG 10 kΩ); the solder jumper on the front adds 2.2 kΩ in parallel, about 550 mA.
Revisions and clones
- Adafruit 1904 (micro-USB): same circuit, no D+/D− pins.
- Unbranded MCP73831 modules (often micro-USB): current is set by a resistor, check the R_PROG marking.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| 5V | 5 V | power input | verifiedVBUS of the USB-C connector: you can power the charger from here or take 5 V from USB. | |
| D- | USB D− | verifiedUSB-C data line: the board can be used as a USB-C adapter.Labelled on other revisions as: D− | ||
| D+ | USB D+ | verified | ||
| GND | Ground | verified | ||
| BAT | 3.7 V | power inputpower output | verifiedBattery positive (same as "+" of the JST connector): 3.0–4.2 V, unregulated.Labelled on other revisions as: VBAT | |
| BAT- | Ground | verifiedJST pin 1: battery negative (common ground).Labelled on other revisions as: − | ||
| BAT+ | 3.7 V | power inputpower output | verifiedJST pin 2: positive. Polarity as on Adafruit batteries; on Chinese ones it is sometimes reversed.Labelled on other revisions as: + |
Sources
Every pin is verified against the manufacturer's documents.
- Adafruit: Adafruit USB C microlipo charger.brd (Eagle)board drawing, checked 17.10.2026outline 22.86×19.05; JP4 row 5V, D−, D+, GND, VBAT at 2.54 pitch along the top edge; JST: 1 GND, 2 VBAT; USB-C with 5.1 kΩ on CC1 and CC2; R_PROG 10 kΩ and 2.2 kΩ through SJ1; red and green LEDs; 4 holes 2.5 mm
- Adafruit Learn: Micro-Lipo and Mini-Lipo battery chargers, Pinoutsuser guide, checked 17.10.20265V, D+/D−, GND, BAT; CHG red: charging, DONE green: charged, both: no battery; 3.7/4.2 V cells only
- Adafruit product 4410: Micro-Lipo Charger with USB Type C Jackuser guide, checked 17.10.2026100 mA from the factory, 500 mA with the front jumper, 24×19×7.2 mm, pins 5V, D−, D+, GND, VBAT
- Microchip MCP73831/2 Li-Ion/Li-Polymer Charge Management Controllerdatasheet, checked 17.10.2026input 3.75–6 V, charge 4.20 V, current 15–500 mA = 1000 V / R_PROG, SOT-23-5
Size: from the Eagle outline (0.9×0.75 inch); 24×19 with the USB-C connector at Adafruit.
You might also need
Schematic with this board
schematic builder with the board already placed
Battery pack builder
S×P layout from 18650, 21700 and LiPo cells, BMS board and charging
Power budget
will the regulator cope and how long the battery lasts
Calculators
LED resistor, voltage divider, battery runtime, 3D print cost, LED strip power supply and pF, nF, µF conversion



