BMS 1S protection board pinout
BMS 1S protection board (3.7 V, DW01 + 8205A), DW01A + FS8205A, 3.7 V logic, 30×7 mm, 4 pins
partly verified17.10.2026
Top view, battery on the left, load on the right.
BuyDownload PNG- Chip
- DW01A + FS8205A
- Logic
- 3.7 V
- Power
- B+ 2.5-4.2 V
Important
- Like the TP4056 with protection, only without the charger: battery on B+ and B−, load and charging on P+ and P−.
- The circuit's common ground is P−, not B−: if you take ground from B−, over-discharge and overcurrent protection won't work.
- Overcharge about 4.25-4.3 V, over-discharge 2.4-3.0 V depending on the board.
- The board's current rating (3 A, 10 A, 20 A) is printed on the board or in the listing: choose one with margin over the motors' inrush current.
- Charge on P+ and P− at 4.2 V (a 1S charger), the load goes to the same terminals.
Revisions and clones
- Built-in protection is present in the TP4056 with protection (tp4056-protected-usbc) and in Adafruit LiPo batteries.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| B- | Negative of the lower cell (through switches to P−) | not verifiedProtection board with no manufacturer: the B−, B+, P−, P+ labels are standard (DW01/HY2120), the pad layout differs between boards. Read the labels on your board.Battery negative. Not the common ground: protection switches sit between B− and P−.Labelled on other revisions as: B−, BAT- | ||
| B+ | 3.7 V | power input | not verifiedProtection board with no manufacturer: the B−, B+, P−, P+ labels are standard (DW01/HY2120), the pad layout differs between boards. Read the labels on your board.Pack positive: 3.0-4.2 V.Labelled on other revisions as: BAT+ | |
| P- | Ground | not verifiedProtection board with no manufacturer: the B−, B+, P−, P+ labels are standard (DW01/HY2120), the pad layout differs between boards. Read the labels on your board.Load and charging negative: this is the circuit's common ground. The protection opens it.Labelled on other revisions as: P−, OUT- | ||
| P+ | 3.7 V | power output | not verifiedProtection board with no manufacturer: the B−, B+, P−, P+ labels are standard (DW01/HY2120), the pad layout differs between boards. Read the labels on your board.Load and charging positive: connected directly to B+ (some boards have no P+ pad, take the positive from B+).Labelled on other revisions as: OUT+ |
Sources
Not verified against the manufacturer: 4 of 4 pins. The pin card says what confirms each one and where sources disagree.
- ShillehTek: 1S 3.7V 3A 2MOS BMS Li-ion 18650 protection board manualthird-party source, checked 17.10.20261S: B+, B−, P+, P−; DW01 and 2 MOSFETs; load and charger on P+ and P−
- done.land: 2S 10A Battery Management Systemsthird-party source, checked 17.10.20262S: B−, BM (midpoint, sometimes B1), B+, P−, P+; charge 8.4–9.0 V on P+ and P−
- Cirkit Designer: 3S BMSthird-party source, checked 17.10.20263S: B−, B1, B2, B+, P−, P+; connect the taps from negative to positive
Size: not dimensioned: protection boards come in different shapes (approximate).
You might also need
Similar boards

BMS 2S protection board (7.4 V, with balancing)
2S protection controller (HY2120/HY2213 and equivalents) + MOSFET5 pins

BMS 3S protection board (11.1 V, with balancing)
3S protection controller (HY2120/HY2213 and equivalents) + MOSFET6 pins

Adafruit Micro-Lipo USB-C LiPo charger (MCP73831, product 4410)
MCP73831T-2ACI/OT7 pins

IP5306 power bank module (2 A charging + 5 V 2 A output, USB-C and USB-A)
IP53065 pins