IP5306 power bank module pinout
IP5306 power bank module (2 A charging + 5 V 2 A output, USB-C and USB-A), IP5306, 5 V logic, 30×20 mm, 5 pins
Top view, USB-C on the left, USB-A on the right, battery and button pads at the bottom.
Download PNG- Chip
- IP5306
- Logic
- 5 V
- Power
- USB-C 4.75-5.5 V
Important
- Battery + charger + 5 V on one board: handy for a robot or a USB lamp.
- Not suitable for an ESP32 that sleeps: at a current under 45 mA the output turns off after 32 s. Work around it with a dummy load resistor (wastes energy) or use a TP4056 with protection + MT3608.
- While charging, the 5 V output can drop out for a fraction of a second when the cable is plugged in: the board will reset.
- Quiescent current is about 50 µA with the output off, milliamps with it on.
- IMPORTANT: with a load under 45 mA for longer than 32 s the IP5306 shuts off the 5 V output (per the datasheet). An ESP32 in deep sleep will lose power; turn it back on with the button (KEY).
Revisions and clones
- IP5306 modules with micro-USB, with the I2C variant of the chip (IP5306_I2C, on M5Stack) and with 5V/GND pads instead of USB-A: same functions.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| B+ | 3.7 V | power inputpower output | not verifiedModule with no manufacturer, no board documentation found: pad placement and labels are approximate. Read the silkscreen on your own board.Positive of a single 4.2 V Li-ion cell. Over-discharge protection in the IP5306 (about 3.0 V) works by load current, it is not a separate switch.Labelled on other revisions as: BAT+, BAT | |
| B- | Ground | not verifiedModule with no manufacturer, no board documentation found: pad placement and labels are approximate. Read the silkscreen on your own board.Battery negative: on the IP5306 this is a common Ground with USB.Labelled on other revisions as: BAT- | ||
| KEY | Button: a short press turns on the output, a double press the flashlight (if present), a long press turns it off | not verifiedModule with no manufacturer, no board documentation found: pad placement and labels are approximate. Read the silkscreen on your own board.Button between KEY and GND. Without a button the output turns on when a load is connected. | ||
| 5V | 5 V | power output | not verifiedModule with no manufacturer, no board documentation found: pad placement and labels are approximate. Read the silkscreen on your own board.Boost output 5.1 V, up to 2.1 A. Many boards have no separate pad: pin 1 of the USB-A socket.Labelled on other revisions as: VOUT, OUT+ | |
| GND | Ground | not verifiedModule with no manufacturer, no board documentation found: pad placement and labels are approximate. Read the silkscreen on your own board.Labelled on other revisions as: OUT- |
Sources
Not verified against the manufacturer: 5 of 5 pins. The pin card says what confirms each one and where sources disagree.
- Injoinic IP5306 datasheet V1.10 (Electrokit copy)datasheet, checked 17.10.2026eSOP-8 pins: 1 VIN, 2-4 LED1-3, 5 KEY, 6 BAT, 7 SW, 8 VOUT; charge 2.1 A, output 5 V 2.1 A, boost efficiency up to 96%; shutdown at load under 45 mA for longer than 32 s; battery standby current 50 µA; input 4.75-5.5 V
- Injoinic: manufacturer's websitethird-party source, checked 17.10.2026maker of the IP5306 chip
Size: not dimensioned: IP5306 modules come in different shapes, about 25-30×17-21 mm (approximate).
You might also need
Schematic with this board
schematic builder with the board already placed
Battery pack builder
S×P layout from 18650, 21700 and LiPo cells, BMS board and charging
Power budget
will the regulator cope and how long the battery lasts
Calculators
LED resistor, voltage divider, battery runtime, 3D print cost, LED strip power supply and pF, nF, µF conversion
Similar boards

Adafruit Micro-Lipo USB-C LiPo charger (MCP73831, product 4410)
MCP73831T-2ACI/OT7 pins

TP4056 charger without protection (4 pads, micro-USB)
TP40564 pins

TP4056 charger with protection (DW01A + 8205A, USB-C)
TP4056 + DW01A + FS8205A6 pins

BMS 1S protection board (3.7 V, DW01 + 8205A)
DW01A + FS8205A4 pins