TP4056 charger without protection pinout
TP4056 charger without protection (4 pads, micro-USB), TP4056, 5 V logic, 27.94×17.1 mm, 4 pins
partly verified15.10.2026
Top view, USB on the left, battery pads on the right.
Download PNG- Chip
- TP4056
- Logic
- 5 V
- Power
- Micro-USB 4.5-5.5 VIN+ 4.5-5.5 V
Important
- For a single Li-ion / Li-Po 3.7 V cell only (charges to 4.2 V). Do not charge LiFePO4 (3.6 V) or NiMH with this module.
- The charge current is set by the R_PROG resistor (usually 1.2 kΩ = 1 A). For small batteries it is changed: 2.4 kΩ = 500 mA, 10 kΩ = 130 mA.
- At 1 A the chip gets noticeably hot and reduces the current by itself.
- Red LED: charging, blue (or green): charged.
- No protection: the battery can be over-discharged, reversing the battery burns the chip. A load during charging disrupts charge termination.
- Geometry from third-party KiCad footprints and seller descriptions (±0.5 mm), small components are drawn approximately. Check with calipers before laying out your own board.
Revisions and clones
- Also comes with USB-C, same layout.
- Version with protection (6 pads, OUT±): entry tp4056-protected-usbc.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| IN+ | 5 V | power input | not from manufacturerNo-name module: IN− bottom left per the AZ-Delivery photo, the other pads from the footprint and descriptions. Which of the right pads is B+, check by the label. | |
| IN- | Ground | not from manufacturerNo-name module: IN− bottom left per the AZ-Delivery photo, the other pads from the footprint and descriptions. Which of the right pads is B+, check by the label.Labelled on other revisions as: IN− | ||
| B+ | 4.2 V | power inputpower output | not from manufacturerNo-name module: IN− bottom left per the AZ-Delivery photo, the other pads from the footprint and descriptions. Which of the right pads is B+, check by the label.Battery and load positive (no protection).Labelled on other revisions as: BAT+ | |
| B- | Ground | not from manufacturerNo-name module: IN− bottom left per the AZ-Delivery photo, the other pads from the footprint and descriptions. Which of the right pads is B+, check by the label.Battery negative: here it is the common ground with IN−.Labelled on other revisions as: BAT-, B− |
Sources
Not verified against the manufacturer: 4 of 4 pins. The pin card says what confirms each one and where sources disagree.
- TP4056 datasheet (NanJing Top Power), SparkFun copydatasheet, checked 15.10.2026VCC 4.0–8.0 V, charge to 4.2 V ±1.5%, R_PROG 1.2 kΩ = 1000 mA, 2.4 kΩ = 500 mA, precharge below 2.9 V, thermal regulation, CHRG and STDBY LEDs
- TeachMePicro: TP4056 charging module pinout and wiringthird-party source, checked 15.10.2026table of R_PROG and currents, red = charging, blue/green = done, connect the load to OUT±, no reverse polarity protection, 4.2 V only
- AZ-Delivery: TP4056 Micro-USB charge controllerthird-party source, checked 15.10.20264 pads, IN− bottom left, 1k2 resistor
- techiesms: TP4056 battery charging module (no protection)third-party source, checked 15.10.2026no protection, reversing the battery burns the chip
- KiCad: lilka-dev/lilka Charge_Controller_TP4056_4pin.kicad_modthird-party source, checked 15.10.2026board 27.94×17.1, pads (1.5; 1.6), (1.5; 15.6), (24.5; 1.6), (24.5; 15.6)
Size: from the lilka-dev footprint (27.94×17.1); sellers list 25×19 and 26×17 (approximate).
You might also need
Schematic with this board
schematic builder with the board already placed
Battery pack builder
S×P layout from 18650, 21700 and LiPo cells, BMS board and charging
Power budget
will the regulator cope and how long the battery lasts
Calculators
LED resistor, voltage divider, battery runtime, 3D print cost, LED strip power supply and pF, nF, µF conversion
Similar boards

Adafruit Micro-Lipo USB-C LiPo charger (MCP73831, product 4410)
MCP73831T-2ACI/OT7 pins

IP5306 power bank module (2 A charging + 5 V 2 A output, USB-C and USB-A)
IP53065 pins

TP4056 charger with protection (DW01A + 8205A, USB-C)
TP4056 + DW01A + FS8205A6 pins

BMS 1S protection board (3.7 V, DW01 + 8205A)
DW01A + FS8205A4 pins