TP4056 charger with protection pinout
TP4056 charger with protection (DW01A + 8205A, USB-C), TP4056 + DW01A + FS8205A, 5 V logic, 28×17 mm, 6 pins
partly verified15.10.2026
Top view, USB on the left, battery and load pads on the right.
BuyDownload PNG- Chip
- TP4056 + DW01A + FS8205A
- Logic
- 5 V
- Power
- USB-C 4.5-5.5 VIN+ 4.5-5.5 V
Important
- For a single Li-ion / Li-Po 3.7 V cell only (charges to 4.2 V). Do not charge LiFePO4 (3.6 V) or NiMH with this module.
- The charge current is set by the R_PROG resistor (usually 1.2 kΩ = 1 A). For small batteries it is changed: 2.4 kΩ = 500 mA, 10 kΩ = 130 mA.
- At 1 A the chip gets noticeably hot and reduces the current by itself.
- Red LED: charging, blue (or green): charged.
- Connect the load to OUT+ and OUT−, the battery to B+ and B−. If the load is connected to B±, the overdischarge protection does not work.
- Geometry from third-party KiCad footprints and seller descriptions (±0.5 mm), small components are drawn approximately. Check with calipers before laying out your own board.
- Protection (per Mischianti): overcharge 4.3 V, overdischarge 2.4 V (recovery 3.0 V), current about 3 A.
Revisions and clones
- Micro-USB variant: same circuit and pad order, the board is usually 26×17 mm. There are no statistics on which connector is more common now; USB-C was chosen as the main one because it is shown more often in 2025 listings.
- Without protection (only the TP4056, 4 pads IN+, IN−, B+, B−) is a separate entry, tp4056-no-protection.
- There are modules on the 03962A (a variant with the TP4056 and protection on one board with a different layout): check the labels.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| IN+ | 5 V | power input | not from manufacturerA module with no manufacturer: pad order from the Mischianti photo and two footprints (they agree), the size from sellers ranges from 22×17 to 28×17.In parallel with USB: you can solder a 5 V wire instead of USB. | |
| IN- | Ground | not from manufacturerA module with no manufacturer: pad order from the Mischianti photo and two footprints (they agree), the size from sellers ranges from 22×17 to 28×17.Connected to OUT− (common ground of the charger and the load).Labelled on other revisions as: IN− | ||
| OUT+ | 4.2 V | power output | not from manufacturerA module with no manufacturer: pad order from the Mischianti photo and two footprints (they agree), the size from sellers ranges from 22×17 to 28×17.Load positive. Electrically the same as B+. | |
| B+ | 4.2 V | power inputpower output | not from manufacturerA module with no manufacturer: pad order from the Mischianti photo and two footprints (they agree), the size from sellers ranges from 22×17 to 28×17.Battery positive.Labelled on other revisions as: BAT+ | |
| B- | Battery negative (through the 8205A switch to OUT−) | not from manufacturerA module with no manufacturer: pad order from the Mischianti photo and two footprints (they agree), the size from sellers ranges from 22×17 to 28×17.Battery negative. Not a common ground: the protection switch sits between B− and OUT−.Labelled on other revisions as: B−, BAT- | ||
| OUT- | Ground | not from manufacturerA module with no manufacturer: pad order from the Mischianti photo and two footprints (they agree), the size from sellers ranges from 22×17 to 28×17.Load negative. The DW01A protection opens it on overdischarge, overcharge and overcurrent.Labelled on other revisions as: OUT− |
Sources
Not verified against the manufacturer: 6 of 6 pins. The pin card says what confirms each one and where sources disagree.
- TP4056 datasheet (NanJing Top Power), SparkFun copydatasheet, checked 15.10.2026VCC 4.0–8.0 V, charge to 4.2 V ±1.5%, R_PROG 1.2 kΩ = 1000 mA, 2.4 kΩ = 500 mA, precharge below 2.9 V, thermal regulation, CHRG and STDBY LEDs
- DW01 battery protection IC datasheet (Fortune), Soldered copydatasheet, checked 15.10.2026overcharge threshold 4.25–4.35 V, overdischarge, overcurrent protection through an external switch
- FS8205A dual N-MOSFET datasheet (Fortune)datasheet, checked 15.10.2026dual 20 V switch, about 25 mΩ (22.5 mΩ for TECH PUBLIC)
- Mischianti: TP4056 LiPo charger, high resolution pinout (2025, photo with USB-C)third-party source, checked 15.10.2026IN+/IN− pads at USB, OUT+, B+, B−, OUT− at the other end (OUT on the edges), module schematic, protection thresholds
- TeachMePicro: TP4056 charging module pinout and wiringthird-party source, checked 15.10.2026table of R_PROG and currents, red = charging, blue/green = done, connect the load to OUT±, no reverse polarity protection, 4.2 V only
- KiCad: slash4you/Anemometre-Girouette TP4056_module.kicad_mod (USB-C) and josefadamcik/RoomMonitorPcb TP4056_Module (micro-USB)third-party source, checked 15.10.2026board 28×17 (26×17 for micro-USB), coordinates of IN±, OUT+, B+, B−, OUT−
Size: 28×17 mm per the slash4you footprint (USB-C); sellers list 26×17, 25×19, 22×17 (approximate).
You might also need
Schematic with this board
schematic builder with the board already placed
Battery pack builder
S×P layout from 18650, 21700 and LiPo cells, BMS board and charging
Power budget
will the regulator cope and how long the battery lasts
Calculators
LED resistor, voltage divider, battery runtime, 3D print cost, LED strip power supply and pF, nF, µF conversion
Similar boards

Adafruit Micro-Lipo USB-C LiPo charger (MCP73831, product 4410)
MCP73831T-2ACI/OT7 pins

IP5306 power bank module (2 A charging + 5 V 2 A output, USB-C and USB-A)
IP53065 pins

TP4056 charger without protection (4 pads, micro-USB)
TP40564 pins

BMS 1S protection board (3.7 V, DW01 + 8205A)
DW01A + FS8205A4 pins