Arduino Due pinout
Arduino Due (SAM3X8E), AT91SAM3X8E, 3.3 V logic, 101.6×53.34 mm, 92 pins
verified17.10.2026
- NC
- IOREF3.3 V
- RESETSAM3X reset
- 3.3V3.3 V
- 5V5 V
- GND
- GND
- VIN7-12 V
- A0PA1654AD7, 12 bit
- A1PA2455AD6, 12 bit
- A2PA2356AD5, 12 bit
- A3PA2257AD4, 12 bit
- A4PA658AD3, 12 bit
- A5PA459AD2, 12 bit
- A6PA360AD1, 12 bit
- A7PA261AD0, 12 bit
- A8PB1762AD10, 12 bit
- A9PB1863AD11, 12 bit
- A10PB1964AD12, 12 bit
- A11PB2065AD13, 12 bit
- DAC0PB156612-bit DAC
- DAC1PB166712-bit DAC
- CANRXPA1CAN0 RX
- CANTXPA0CAN0 TX
- GND
- GND
- 52PB21SPI CS
- 53PB14
- 50PC13
- 51PC12
- 48PC15
- 49PC14
- 46PC17
- 47PC16
- 44PC19
- 45PC18
- 42PA19
- 43PA20
- 40PC8
- RESETSAM3X reset
- GND
- 41PC9
- SCL1PA18I2C SCL1
- SDA1PA17I2C SDA1
- AREFADC reference voltage3.3 V
- GND
- 13PB27LEDPWM
- 12PD8PWM
- 11PD7PWM
- 10PC29SPI CSPWM
- 9PC21PWM
- 8PC22PWM
- 7PC23PWM
- 6PC24PWM
- 5PC25PWM
- 4PC26SPI CSPWM
- 3PC28PWM
- 2PB25PWM
- TX→1PA91Serial TX
- RX←0PA80Serial RX
- TX3 14PD414Serial3 TX
- RX3 15PD515Serial3 RX
- TX2 16PA1316Serial2 TX
- RX2 17PA1217Serial2 RX
- TX1 18PA1118Serial1 TX
- RX1 19PA1019Serial1 RX
- SDA 20PB1220I2C SDA
- SCL 21PB1321I2C SCL
- 5V5 V
- 5V5 V
- 22PB26
- 23PA14
- 24PA15
- 25PD0
- 26PD1
- 27PD2
- 28PD3
- 29PD6
- 30PD9
- 31PA7
- 32PD10
- 33PC1
- 34PC2
- 35PC3
- 36PC4
- MISOPA25SPI MISO
- +5V5 V
- 37PC5
- 38PC6
- SCKPA27SPI SCK
- MOSIPA26SPI MOSI
- 39PC7
Top view, USB and DC jack on the left, rotated 90° on the diagram.
CompareDownload PNG- Chip
- AT91SAM3X8E
- Logic
- 3.3 V
- Power
- Micro-USB "Programming" or "Native" 4.75-5.25 VVIN / DC jack 7-12 V5V
- Defaults in ArduinoCore-sam (arduino_due_x)
- I2C: SDA 20, SCL 21SPI: MOSI 75, MISO 74, SCK 76, SS 10UART: TX 1, RX 0LED: 13
Which Arduino Due pins are safe to use
Free to use
D0-D12, D14-D19, D22-D53, A0-A11, DAC0, DAC1, SCL1, SDA1, CANRX, CANTX, MISO, MOSI, SCK
Use with care
- D13: onboard LED.
- D20, D21: onboard pull-up or divider.
Important
- 3.3 V logic! Looks like a Mega, but 5 V must not be applied to pins: the SAM3X burns out. 5 V shields only with IOREF or through a level shifter.
- SPI only on the 6-pin SPI header in the middle of the board (not on 50–53 as on the Mega).
- I2C: Wire on 20/21 (with 1.5 kΩ pull-ups), Wire1 on SDA1/SCL1 near AREF.
- Two USB ports: "Programming" (through the 16U2, resets the board when the port is opened) and "Native" (SerialUSB, can be a host for a keyboard).
- The DAC0/DAC1 outputs are roughly 0.55–2.75 V, not 0–3.3 V.
- Pin current is small (3–15 mA), up to 130 mA for all pins together.
- Positions of buttons, chips and USB connectors are drawn approximately; header connectors follow the Mega files.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| SCL1 | PA18 | interrupt (any pin)I2C SCL1 (Wire1) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together.Second I2C (Wire1, TWCK0), not the same as 21 on the Mega. No pull-ups on the board. |
| SDA1 | PA17 | interrupt (any pin)I2C SDA1 (Wire1) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together.Second I2C (Wire1, TWD0). No pull-ups on the board. |
| AREF | 3.3 VADC reference voltage | power input | verifiedTied to 3.3 V through a resistor on the board by default. Not above 3.3 V. | |
| GND | Ground | verified | ||
| 13 | PB27, Arduino 13 | interrupt (any pin)PWM (TIOB0) | not 5 V tolerantonboard LED | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together.L LED on the board. LED_BUILTIN = 13. |
| 12 | PD8, Arduino 12 | interrupt (any pin)PWM (TIOB8) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 11 | PD7, Arduino 11 | interrupt (any pin)PWM (TIOA8) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 10 | PC29, Arduino 10 | interrupt (any pin)PWM (TIOB7)SPI CS (NPCS0, second pin PA28) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 9 | PC21, Arduino 9 | interrupt (any pin)PWM (PWML4) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 8 | PC22, Arduino 8 | interrupt (any pin)PWM (PWML5) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 7 | PC23, Arduino 7 | interrupt (any pin)PWM (PWML6) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 6 | PC24, Arduino 6 | interrupt (any pin)PWM (PWML7) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 5 | PC25, Arduino 5 | interrupt (any pin)PWM (TIOA6) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 4 | PC26, Arduino 4 | interrupt (any pin)PWM (TIOB6)SPI CS (NPCS1, second pin PA29) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 3 | PC28, Arduino 3 | interrupt (any pin)PWM (TIOA7) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 2 | PB25, Arduino 2 | interrupt (any pin)PWM (TIOA0) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| TX→1 | PA9, Arduino 1 | interrupt (any pin)Serial TX (through ATmega16U2) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| RX←0 | PA8, Arduino 0 | interrupt (any pin)Serial RX (through ATmega16U2) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| TX3 14 | PD4, Arduino 14 | interrupt (any pin)Serial3 TX | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| RX3 15 | PD5, Arduino 15 | interrupt (any pin)Serial3 RX | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| TX2 16 | PA13, Arduino 16 | interrupt (any pin)Serial2 TX | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| RX2 17 | PA12, Arduino 17 | interrupt (any pin)Serial2 RX | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| TX1 18 | PA11, Arduino 18 | interrupt (any pin)Serial1 TX | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| RX1 19 | PA10, Arduino 19 | interrupt (any pin)Serial1 RX | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| SDA 20 | PB12, Arduino 20 | interrupt (any pin)I2C SDA (Wire) | not 5 V tolerantonboard pull-up | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together.1.5 kΩ pull-up to 3.3 V on the board. |
| SCL 21 | PB13, Arduino 21 | interrupt (any pin)I2C SCL (Wire) | not 5 V tolerantonboard pull-up | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together.1.5 kΩ pull-up to 3.3 V on the board. |
| - | not connected | verifiedNot connected (reserved). | ||
| IOREF | 3.3 V | power output | verifiedBoard logic voltage is 3.3 V: shields with IOREF will switch, others on 5 V will burn the SAM3X. | |
| RESET | SAM3X reset (low = reset) | verified | ||
| 3.3V | 3.3 V | power output | verified3.3 V regulator: up to 800 mA for modules (Due specifications). | |
| 5V | 5 V | power inputpower output | verifiedUp to 800 mA from the board's switching regulator (Due specifications). | |
| GND | Ground | verified | ||
| GND | Ground | verified | ||
| VIN | 9 V | power input | verifiedRegulator input: 7–12 V, limit 6–16 V. | |
| A0 | PA16, Arduino A0 (54) | interrupt (any pin)AD7, 12 bit | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| A1 | PA24, Arduino A1 (55) | interrupt (any pin)AD6, 12 bit | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| A2 | PA23, Arduino A2 (56) | interrupt (any pin)AD5, 12 bit | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| A3 | PA22, Arduino A3 (57) | interrupt (any pin)AD4, 12 bit | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| A4 | PA6, Arduino A4 (58) | interrupt (any pin)AD3, 12 bit | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| A5 | PA4, Arduino A5 (59) | interrupt (any pin)AD2, 12 bit | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| A6 | PA3, Arduino A6 (60) | interrupt (any pin)AD1, 12 bit | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| A7 | PA2, Arduino A7 (61) | interrupt (any pin)AD0, 12 bit | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| A8 | PB17, Arduino A8 (62) | interrupt (any pin)AD10, 12 bit | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| A9 | PB18, Arduino A9 (63) | interrupt (any pin)AD11, 12 bit | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| A10 | PB19, Arduino A10 (64) | interrupt (any pin)AD12, 12 bit | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| A11 | PB20, Arduino A11 (65) | interrupt (any pin)AD13, 12 bit | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| DAC0 | PB15, Arduino DAC0 (66) | interrupt (any pin)12-bit DAC (DAC0) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together.12-bit DAC output: range roughly 1/6 to 5/6 of 3.3 V (0.55–2.75 V), not from zero. It cannot drive a load: current of a few mA. |
| DAC1 | PB16, Arduino DAC1 (67) | interrupt (any pin)12-bit DAC (DAC1) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together.12-bit DAC output: range roughly 0.55–2.75 V. It cannot drive a load. |
| CANRX | PA1 | interrupt (any pin)CAN0 RX | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together.CAN0 RX: needs an external transceiver (MCP2551, SN65HVD230). |
| CANTX | PA0 | interrupt (any pin)CAN0 TX | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together.CAN0 TX: needs an external transceiver. |
| 5V | 5 V | power inputpower output | verified | |
| 22 | PB26, Arduino 22 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 24 | PA15, Arduino 24 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 26 | PD1, Arduino 26 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 28 | PD3, Arduino 28 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 30 | PD9, Arduino 30 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 32 | PD10, Arduino 32 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 34 | PC2, Arduino 34 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 36 | PC4, Arduino 36 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 38 | PC6, Arduino 38 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 40 | PC8, Arduino 40 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 42 | PA19, Arduino 42 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 44 | PC19, Arduino 44 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 46 | PC17, Arduino 46 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 48 | PC15, Arduino 48 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 50 | PC13, Arduino 50 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 52 | PB21, Arduino 52 | interrupt (any pin)SPI CS (NPCS2) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| GND | Ground | verified | ||
| 5V | 5 V | power inputpower output | verified | |
| 23 | PA14, Arduino 23 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 25 | PD0, Arduino 25 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 27 | PD2, Arduino 27 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 29 | PD6, Arduino 29 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 31 | PA7, Arduino 31 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 33 | PC1, Arduino 33 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 35 | PC3, Arduino 35 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 37 | PC5, Arduino 37 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 39 | PC7, Arduino 39 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 41 | PC9, Arduino 41 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 43 | PA20, Arduino 43 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 45 | PC18, Arduino 45 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 47 | PC16, Arduino 47 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 49 | PC14, Arduino 49 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 51 | PC12, Arduino 51 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| 53 | PB14, Arduino 53 | interrupt (any pin) | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| GND | Ground | verified | ||
| MISO | PA25 | interrupt (any pin)SPI MISO | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| +5V | 5 V | power inputpower output | verified | |
| SCK | PA27 | interrupt (any pin)SPI SCK | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| MOSI | PA26 | interrupt (any pin)SPI MOSI | not 5 V tolerant | verifiedPin current 3 or 15 mA as output and 6 or 9 mA as input depending on the pin (SAM3X datasheet), up to 130 mA for all pins together. |
| RESET | SAM3X reset | verified | ||
| GND | Ground | verified |
Sources
Every pin is verified against the manufacturer's documents.
- Arduino Due (A000062): specifications and pinoutdatasheet, checked 17.10.20263.3 V logic, not 5 V tolerant, 54 digital pins (12 PWM), 12 analog, 2 DACs, 4 UARTs, 2 I2C, CAN, SPI only on the 6-pin header, 3.3 V and 5 V current 800 mA each, 130 mA total on pins
- ArduinoCore-sam: variants/arduino_due_x/variant.cppArduino core, checked 17.10.2026D0–D53, A0–A11, DAC0/1, CANRX/TX, SDA1/SCL1, MISO/MOSI/SCK ↔ SAM3X8E ports, PWM (TIOA/TIOB/PWML) on 2–13
- Arduino MEGA 2560 R3: Eagle files (connectors shared with Due)board drawing, checked 17.10.2026size 101.6×53.34 mm and connector pad centers, the same on Mega and Due
Size: size and connectors same as Mega 2560 R3; components approximate.
FAQ
- Which Arduino Due pins are I2C, SPI and UART?
- By default in ArduinoCore-sam (arduino_due_x): I2C: SDA D20, SCL D21; SPI: MOSI D75, MISO D74, SCK D76, SS D10; UART: TX D1, RX D0.
- Which pin is the Arduino Due LED on?
- L LED on D13.
- Are the Arduino Due pins 5 V tolerant?
- No. The logic is 3.3 V and the pins are not 5 V tolerant: use a divider or a level shifter for 5 V signals.
You might also need
Similar boards
Next
Need firmware or a device built on AT91SAM3X8E? I'll build it to order



