Arduino Nano 33 IoT pinout
Arduino Nano 33 IoT (SAMD21, Wi-Fi), ATSAMD21G18A, 3.3 V logic, 45×18 mm, 30 pins
verified17.10.2026
- D13PA1713LEDSPI SCK
- 3.3V3.3 V
- AREFADC reference voltage3.3 V
- A0PA0214AIN0, 12 bit10-bit DAC
- A1PB0215AIN10
- A2PA1116AIN19PWM TCC0
- A3PA1017AIN18PWM TCC0
- A4PB0818I2C SDAAIN2
- A5PB0919I2C SCLAIN3PWM TC4
- A6PA0920AIN17
- A7PB0321AIN11
- VUSB5 V
- RSTReset
- GND
- VIN4.5-21 V
Top view, USB on the left (as on the official pinout), rotated 90° on the diagram.
CompareDownload PNG- Chip
- ATSAMD21G18A, u-blox NINA-W102 (ESP32, Wi-Fi and Bluetooth)
- Logic
- 3.3 V
- Power
- Micro-USB 4.8-5.25 VVIN 4.5-21 V
- Defaults in ArduinoCore-samd (nano_33_iot)
- I2C: SDA 18, SCL 19SPI: MOSI 11, MISO 12, SCK 13, SS 10UART: TX 1, RX 0LED: 13
Which Arduino Nano 33 IoT pins are safe to use
Free to use
D0-D12, A0-A7
Use with care
- D13: onboard LED.
Important
- 3.3 V logic, don't apply 5 V to the pins (datasheet: NOT 5V tolerant).
- The "5V" pin here is VUSB and is not connected anywhere by default: you cannot take 5 V for modules from the board without a jumper.
- Wi-Fi and Bluetooth: NINA-W102 module over SPI (SERCOM2), libraries WiFiNINA and ArduinoBLE.
- I2C A4/A5 are already used by the LSM6DS3 IMU (0x6A) and the ATECC608A (0x60): sensor addresses must not collide.
- Current per pin up to 7 mA.
- Pin rows follow 2.54 mm pitch and 0.6 in width; small components are drawn approximately.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| D12 | PA19, Arduino 12 | PWM TC3SPI MISO (SERCOM1) | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| D11 | PA16, Arduino 11 | PWM TCC2EXTINT0SPI MOSI (SERCOM1) | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| D10 | PA21, Arduino 10 | PWM TCC0EXTINT5SPI SS | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| D9 | PA20, Arduino 9 | PWM TCC0EXTINT4 | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| D8 | PA18, Arduino 8 | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. | |
| D7 | PA06, Arduino 7 | AIN6 | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| D6 | PA04, Arduino 6 | PWM TCC0AIN4 | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| D5 | PA05, Arduino 5 | PWM TCC0AIN5 | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| D4 | PA07, Arduino 4 | PWM TCC1AIN7 | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| D3 | PB11, Arduino 3 | PWM TC5EXTINT11 | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| D2 | PB10, Arduino 2 | PWM TC5EXTINT10 | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| GND | Ground | verified | ||
| RST | Reset (low = reset) | onboard button | verified | |
| RX0 | PB23, Arduino 0 | Serial1 RX (SERCOM5) | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| TX1 | PB22, Arduino 1 | Serial1 TX (SERCOM5) | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| D13 | PA17, Arduino 13 | EXTINT1SPI SCK (SERCOM1) | not 5 V tolerantonboard LED | verifiedCurrent per pin up to 7 mA.L LED on the board. LED_BUILTIN = 13. |
| 3.3V | 3.3 V | power output | verifiedMPM3610 DC-DC 3.3 V output: powers the board and modules. | |
| AREF | 3.3 VADC reference voltage | power input | verified | |
| A0 | PA02, Arduino A0 (14) | AIN0, 12 bit10-bit DAC (DAC0) | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| A1 | PB02, Arduino A1 (15) | AIN10EXTINT2 | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| A2 | PA11, Arduino A2 (16) | AIN19PWM TCC0 | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| A3 | PA10, Arduino A3 (17) | AIN18PWM TCC0 | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| A4 | PB08, Arduino A4 (18) | AIN2I2C SDA (SERCOM4) | not 5 V tolerant | verifiedBoard I2C bus: the LSM6DS3 IMU (0x6A) and the ATECC608A chip (0x60) are on it too. Arduino does not recommend analogRead on A4/A5.Current per pin up to 7 mA. |
| A5 | PB09, Arduino A5 (19) | AIN3PWM TC4EXTINT9I2C SCL (SERCOM4) | not 5 V tolerant | verifiedBoard I2C bus: the IMU and ATECC608A are on it too.Current per pin up to 7 mA. |
| A6 | PA09, Arduino A6 (20) | AIN17 | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| A7 | PB03, Arduino A7 (21) | AIN11EXTINT3 | not 5 V tolerant | verifiedCurrent per pin up to 7 mA. |
| VUSB | 5 V | power inputpower output | verifiedUsually not connected: it joins the 5 V of the USB connector if you solder the VUSB jumper on the back. | |
| RST | Reset (low = reset) | verified | ||
| GND | Ground | verified | ||
| VIN | 5 V | power input | verifiedMPM3610 DC-DC input: 4.5–21 V. |
Sources
Every pin is verified against the manufacturer's documents.
- Arduino Nano 33 IoT Datasheet (ABX00027)datasheet, checked 17.10.202630-pin table (VUSB is usually not connected, jumper SJ1), 3.3 V logic and not 5 V tolerant, VIN up to 21 V on the MPM3610, NINA-W102, IMU and ATECC608A on I2C
- ArduinoCore-samd: variants/nano_33_iot/variant.cppArduino core, checked 17.10.2026D0–D13, A0–A7 ↔ SAMD21 ports, PWM (TC/TCC), EXTINT, SPI SERCOM1 on 11/12/13, I2C SERCOM4 on A4/A5, Serial1 SERCOM5 on 0/1, SERCOM2 talks to the NINA
Size: 45×18 mm per the datasheet; rows 15.24 mm apart at 2.54 mm pitch, position along the board is centered.
FAQ
- Which Arduino Nano 33 IoT pins are I2C, SPI and UART?
- By default in ArduinoCore-samd (nano_33_iot): I2C: SDA A4, SCL A5; SPI: MOSI D11, MISO D12, SCK D13, SS D10; UART: TX D1, RX D0.
- Which pin is the Arduino Nano 33 IoT LED on?
- D13.
- Are the Arduino Nano 33 IoT pins 5 V tolerant?
- No. The logic is 3.3 V and the pins are not 5 V tolerant: use a divider or a level shifter for 5 V signals.
You might also need
Similar boards
Next
Need firmware or a device built on ATSAMD21G18A? I'll build it to order



