DS18B20 KY-001 module pinout
DS18B20 KY-001 module (S, +V, −), DS18B20, 3.3 V logic, 15×18.5 mm, 3 pins
partly verified20.10.2026
Top view, sensor at the top, header at the bottom: −, +V, S from left to right (as in the Joy-IT connection drawing).
Download PNG- Chip
- DS18B20
- Logic
- 3.3 V
- Power
- +V (middle pin) 3-5.5 V
Important
- To ESP32: +V to 3V3, − to GND, S to a GPIO with output (not 34-39). The pull-up is already on the board.
- To Arduino: +V to 5V, S to D2 or D4 (Joy-IT example), − to GND.
- OneWire and DallasTemperature libraries, the same on ESP32.
- Board and parts are drawn from Joy-IT photos, dimensions not measured.
Revisions and clones
- Some KY-001 modules are labeled S, +, − or DAT, VCC, GND; check the order against the silkscreen.
- Adapters for a waterproof probe with a terminal block and resistor: labels and order differ between sellers, check the silkscreen.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| - | Ground | not from manufacturerNo module schematic: the order and labels follow the Joy-IT connection drawing (−, +V, S). KY-001 clones may use other labels; the pull-up value is from the photo. Check the silkscreen on your board.Labelled on other revisions as: −, GND, G | ||
| +V | 3.3 V | power input | not from manufacturerNo module schematic: the order and labels follow the Joy-IT connection drawing (−, +V, S). KY-001 clones may use other labels; the pull-up value is from the photo. Check the silkscreen on your board.The middle pin is unlabeled on the board.Labelled on other revisions as: VCC, +, V | |
| S | 1-Wire: DS18B20 data | onboard pull-up | not from manufacturerNo module schematic: the order and labels follow the Joy-IT connection drawing (−, +V, S). KY-001 clones may use other labels; the pull-up value is from the photo. Check the silkscreen on your board.Pull-up to +V is on the board: no external resistor needed.Labelled on other revisions as: Signal, DQ, DAT, OUT |
Sources
Not verified against the manufacturer: 3 of 3 pins. The pin card says what confirms each one and where sources disagree.
- Joy-IT KY001 Temperature sensor, datasheet (05.09.2023)user guide, checked 20.10.2026DS18B20, 1-Wire, operating voltage 3.3 V, 15×25×8 mm; the photo shows a header labeled S and −
- Joy-IT KY-001 Temperatursensor, Anleitung (23.04.2024)user guide, checked 20.10.2026connection drawing: − on the left, +V in the middle, S on the right; Signal to D4, +V to 5V, GND to GND on Arduino; +V to 3.3 V on Raspberry Pi
- Maxim DS18B20 Programmable Resolution 1-Wire Digital Thermometer (REV 042208, Adafruit copy)datasheet, checked 20.10.2026TO-92, view of the marking: 1 GND, 2 DQ, 3 VDD; supply 3.0–5.5 V; active current 1–1.5 mA, standby 750–1000 nA; 4.7 kΩ pull-up; parasitic power from VDD to GND with a strong pull-up during measurement, not recommended above 100 °C; 12 bit up to 750 ms
Size: Joy-IT: 15×25×8 mm including the header; board and parts from the photo, not dimensioned (approximate).
FAQ
- What supply voltage does the DS18B20 KY-001 module need?
- +V (middle pin): 3-5.5 V. 3.3 V logic.



