ESP32-H2 DevKitM-1 pinout
ESP32-H2-DevKitM-1, ESP32-H2, 3.3 V logic, 25.4×48.26 mm, 30 pins
verified17.10.2026
- 3V33.3 V
- RSTbuttonCHIP_PU
- 0GPIO0SPI SSFSPIQ
- 1GPIO1FSPICS0ADC1_CH0
- 2GPIO2BOOTFSPIWPADC1_CH1JTAG MTMS
- 3GPIO3BOOTFSPIHDADC1_CH2JTAG MTDO
- 13/NGPIO13RTC GPIOXTAL_32K_P
- 14/NGPIO14RTC GPIOXTAL_32K_N
- 4GPIO4FSPICLKADC1_CH3JTAG MTCK
- 5GPIO5FSPIDADC1_CH4JTAG MTDI
- NC
- VBAT3-3.6 V
- G
- 5V5 V
- G
Top view, two USB-C ports at the bottom, module antenna at the top.
CompareDownload PNG- Chip
- ESP32-H2, ESP32-H2-MINI-1 (4 MB flash in the package)
- Logic
- 3.3 V
- Power
- USB-C «UART» (CP2102N) 4.75-5.25 VUSB-C "USB" (built-in USB Serial/JTAG) 4.75-5.25 V5V 4.75-5.25 V3V3 3-3.6 VVBAT 3-3.6 V
- Defaults in arduino-esp32 (ESP32H2 Dev Module)
- I2C: SDA 12, SCL 22SPI: MOSI 25, MISO 11, SCK 10, SS 0UART: TX 24, RX 23
Which ESP32-H2 DevKitM-1 pins are safe to use
Free to use
GPIO0, GPIO1, GPIO4, GPIO5, GPIO10-14, GPIO22, GPIO23
Use with care
- GPIO2, GPIO3, GPIO8, GPIO9, GPIO25: strapping: the level at power-up selects the boot mode.
- GPIO24: signal at boot.
- GPIO26, GPIO27: USB lines: use them and you lose USB flashing and the serial port.
Important
- 3.3 V logic, don't put 5 V on the GPIO.
- The ESP32-H2 has no Wi-Fi: only Bluetooth LE and 802.15.4 (Zigbee, Thread, Matter).
- Strapping pins: 2, 3, 8 (RGB LED), 9 (BOOT button), 25.
- 13/N and 14/N are taken by the 32.768 kHz crystal on boards from 2024.
- ADC: GPIO1-5 (ADC1_CH0-4). Wake from deep sleep: GPIO8-14.
- Small components are drawn approximately; pins, module and board follow the dimensional drawing.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| 3V3 | 3.3 V | power inputpower output | verified | |
| RST | CHIP_PU: enable and reset (low = reset) | onboard pull-uponboard button | verifiedRESET button on the board. | |
| 0 | GPIO0 | interruptPWM (LEDC)FSPIQSPI SS | not 5 V tolerant | verified |
| 1 | GPIO1 | interruptPWM (LEDC)ADC1_CH0FSPICS0 | not 5 V tolerant | verified |
| 2 | GPIO2 | interruptPWM (LEDC)ADC1_CH1FSPIWPJTAG MTMS | affects boot (strapping)not 5 V tolerant | verifiedStrapping pin (MTMS): do not hard-pull at reset, see the datasheet.JTAG pins: JTAG goes over USB by default, so these pins are free. |
| 3 | GPIO3 | interruptPWM (LEDC)ADC1_CH2FSPIHDJTAG MTDO | affects boot (strapping)not 5 V tolerant | verifiedStrapping pin (MTDO): do not hard-pull at reset, see the datasheet.JTAG pins: JTAG goes over USB by default, so these pins are free. |
| 13/N | GPIO13 | interruptPWM (LEDC)RTC GPIO: wake from deep sleepXTAL_32K_P | not 5 V tolerant | verifiedOn the board (since February 2024, PW-2024-02-0362) the module's 32.768 kHz crystal is connected here: while it is fitted, do not use the pin. The "/N" label means not for GPIO. |
| 14/N | GPIO14 | interruptPWM (LEDC)RTC GPIO: wake from deep sleepXTAL_32K_N | not 5 V tolerant | verifiedOn the board (since February 2024, PW-2024-02-0362) the module's 32.768 kHz crystal is connected here: while it is fitted, do not use the pin. The "/N" label means not for GPIO. |
| 4 | GPIO4 | interruptPWM (LEDC)ADC1_CH3FSPICLKJTAG MTCK | not 5 V tolerant | verifiedJTAG pins: JTAG goes over USB by default, so these pins are free. |
| 5 | GPIO5 | interruptPWM (LEDC)ADC1_CH4FSPIDJTAG MTDI | not 5 V tolerant | verifiedJTAG pins: JTAG goes over USB by default, so these pins are free. |
| NC | not connected | verified | ||
| VBAT | 3.3 V | power input | verifiedModule power: 3.3 V or battery. | |
| G | Ground | verified | ||
| 5V | 5 V | power inputpower output | verified | |
| G | Ground | verified | ||
| G | Ground | verified | ||
| TX | GPIO24 | interruptPWM (LEDC)UART0 TXFSPICS2 | outputs a signal at bootnot 5 V tolerant | verifiedConnected to the CP2102N ("UART" port). |
| RX | GPIO23 | interruptPWM (LEDC)UART0 RXFSPICS1 | not 5 V tolerant | verifiedConnected to the CP2102N ("UART" port). |
| 10 | GPIO10 | interruptPWM (LEDC)RTC GPIO: wake from deep sleepZCD0 (comparator)SPI SCK | not 5 V tolerant | verified |
| 11 | GPIO11 | interruptPWM (LEDC)RTC GPIO: wake from deep sleepZCD1 (comparator)SPI MISO | not 5 V tolerant | verified |
| 25 | GPIO25 | interruptPWM (LEDC)FSPICS3SPI MOSI | affects boot (strapping)not 5 V tolerant | verifiedStrapping pin: selects the JTAG source. Does not affect normal operation by default. |
| 12 | GPIO12 | interruptPWM (LEDC)RTC GPIO: wake from deep sleepI2C SDA | not 5 V tolerant | verified |
| 8 | GPIO8 | interruptPWM (LEDC)RTC GPIO: wake from deep sleep | affects boot (strapping)not 5 V tolerantonboard LED | verifiedStrapping pin: must be high when entering download boot (GPIO9 = 0); also controls the ROM log output. Do not pull to Ground at reset.Addressable RGB LED WS2812B on the board. |
| 22 | GPIO22 | interruptPWM (LEDC)I2C SCL | not 5 V tolerant | verified |
| G | Ground | verified | ||
| 9 | GPIO9 | interruptPWM (LEDC)RTC GPIO: wake from deep sleep | affects boot (strapping)not 5 V tolerantonboard button | verifiedStrapping: low at reset = firmware download mode (BOOT button). Internal pull-up.BOOT button on the board. |
| G | Ground | verified | ||
| 27 | GPIO27 | interruptPWM (LEDC)USB D+FSPICS5 | USB linenot 5 V tolerant | verifiedBuilt-in USB line (Serial/JTAG or OTG). If you use it as GPIO, the port and flashing over this USB disappear.Connected to the board "USB" port (D+). |
| 26 | GPIO26 | interruptPWM (LEDC)USB D−FSPICS4 | USB linenot 5 V tolerant | verifiedBuilt-in USB line (Serial/JTAG or OTG). If you use it as GPIO, the port and flashing over this USB disappear.Connected to the board "USB" port (D−). |
| G | Ground | verified |
Sources
Every pin is verified against the manufacturer's documents.
- ESP32-H2-DevKitM-1 User Guide (Espressif), Header Block J1/J3user guide, checked 17.10.2026functions of all 30 pins of J1 and J3, 13/N and 14/N taken by the 32 kHz crystal, VBAT, RGB LED on GPIO8, two USB-C ports
- ESP32-H2-DevKitM-1 v1.2 dimensions (PDF)board drawing, checked 17.10.2026board 25.40×48.26 mm, rows 22.86 mm apart, lowest pin 11.125 mm from the bottom edge, module 13.20 mm overhangs by 5.40 mm, silkscreen
- ESP32-H2-DevKitM-1 v1.3 schematicschematic, checked 17.10.2026CP2102N, SGM2212-3.3, WS2812B, ESP32-H2-MINI-1
- ESP32-H2 Series Datasheet (Espressif)datasheet, checked 17.10.2026pin functions: ADC1_CH0-4 on GPIO1-5, JTAG GPIO2-5, XTAL_32K on GPIO13/14, UART0 GPIO23/24, USB GPIO26/27, flash GPIO15-21
- ESP-IDF: GPIO (ESP32-H2)user guide, checked 17.10.2026strapping GPIO2, 3, 8, 9, 25; flash GPIO15-21; USB-JTAG GPIO26/27; RTC GPIO7-14 (wake-up); ADC1_CH0-4 on GPIO1-5; comparator on GPIO10/11
- arduino-esp32: variants/esp32h2/pins_arduino.hArduino core, checked 17.10.2026defaults: TX 24, RX 23, SDA 12, SCL 22, SS 0, MOSI 25, MISO 11, SCK 10, RGB LED 8
Size: per the Espressif dimensional drawing v1.2.
FAQ
- Which ESP32-H2 DevKitM-1 pins are I2C, SPI and UART?
- By default in arduino-esp32 (ESP32H2 Dev Module): I2C: SDA GPIO12, SCL GPIO22; SPI: MOSI GPIO25, MISO GPIO11, SCK GPIO10, SS GPIO0; UART: TX GPIO24, RX GPIO23.
- Which pin is the ESP32-H2 DevKitM-1 LED on?
- WS2812B RGB LED on GPIO8.
- Are the ESP32-H2 DevKitM-1 pins 5 V tolerant?
- No. The logic is 3.3 V and the pins are not 5 V tolerant: use a divider or a level shifter for 5 V signals.
You might also need
Schematic with this board
schematic builder with the board already placed
Flash this board
upload a sketch or .bin to this board from the browser
Power budget
will the regulator cope and how long the battery lasts
Calculators
LED resistor, voltage divider, battery runtime, 3D print cost, LED strip power supply and pF, nF, µF conversion
Similar boards
Next
- Emotion keychainmy ESP32-C5 project, prototype
- ESP32 music playermy ESP32 project, prototype
- DITHR//CAMmy ESP32 project, prototype
Need firmware or a device built on ESP32? I'll build it to order



