ESP32-C6 DevKitC-1 pinout
ESP32-C6-DevKitC-1, ESP32-C6, 3.3 V logic, 25.4×51.8 mm, 32 pins
verified17.10.2026
- 3V33.3 V
- RSTbuttonCHIP_PU
- 4GPIO4BOOTFSPIHDLP_UART RXADC1_CH4LP_GPIO4JTAG MTMS
- 5GPIO5BOOTFSPIWPLP_UART TXADC1_CH5LP_GPIO5JTAG MTDI
- 6GPIO6LP_I2C SDAFSPICLKADC1_CH6LP_GPIO6JTAG MTCK
- 7GPIO7LP_I2C SCLFSPIDLP_GPIO7JTAG MTDO
- 0GPIO0LP_UART DTRADC1_CH0LP_GPIO0XTAL_32K_P
- 1GPIO1LP_UART DSRADC1_CH1LP_GPIO1XTAL_32K_N
- 8GPIO8BOOTLED
- 10GPIO10
- 11GPIO11
- 2GPIO2FSPIQLP_UART RTSADC1_CH2LP_GPIO2
- 3GPIO3LP_UART CTSADC1_CH3LP_GPIO3
- 5V5 V
- G
- NC
Top view, two USB-C ports at the bottom, module antenna at the top.
CompareDownload PNG- Chip
- ESP32-C6, ESP32-C6-WROOM-1 (8 MB flash)
- Logic
- 3.3 V
- Power
- USB-C «UART» (CP2102N) 4.75-5.25 VUSB-C "USB" (built-in USB Serial/JTAG) 4.75-5.25 V5V 4.75-5.25 V3V3 3-3.6 V
- Defaults in arduino-esp32 (ESP32C6 Dev Module)
- I2C: SDA 23, SCL 22SPI: MOSI 19, MISO 20, SCK 21, SS 18UART: TX 16, RX 17
Which ESP32-C6 DevKitC-1 pins are safe to use
Free to use
GPIO0-3, GPIO6, GPIO7, GPIO10, GPIO11, GPIO17-23
Use with care
- GPIO4, GPIO5, GPIO8, GPIO9, GPIO15: strapping: the level at power-up selects the boot mode.
- GPIO12, GPIO13: USB lines: use them and you lose USB flashing and the serial port.
- GPIO16: signal at boot.
Important
- 3.3 V logic, don't put 5 V on the GPIO.
- Strapping: 4, 5, 8 (RGB LED), 9 (BOOT button), 15. Don't pull GPIO8 and 9 to ground at power-up.
- ADC: GPIO0–6 (ADC1_CH0–6), the C6 has no ADC2, so the ADC works with Wi-Fi too.
- LP GPIO0–7 work in deep sleep (LP core, LP_UART on 4/5, LP_I2C on 6/7).
- The "USB" port is the chip's built-in USB on GPIO12/13. If you use these pins, the port disappears.
- Small components are drawn approximately; pins, module and board follow the dimensional drawing.
Revisions and clones
- Also comes with the ESP32-C6-WROOM-1U module (external antenna connector). Schematics v1.2, v1.3, v1.4 differ in small details, the pins are the same.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| 3V3 | 3.3 V | power inputpower output | verified | |
| RST | CHIP_PU: enable and reset (low = reset) | onboard pull-uponboard button | verifiedRESET button on the board. | |
| 4 | GPIO4 | interruptPWM (LEDC)ADC1_CH4LP_GPIO4JTAG MTMSLP_UART RXFSPIHD | affects boot (strapping)not 5 V tolerant | verifiedStrapping (MTMS): together with GPIO5 sets the SDIO slave clock edges. Don't pull it hard at reset.JTAG pins: JTAG goes over USB by default, so these pins are free. |
| 5 | GPIO5 | interruptPWM (LEDC)ADC1_CH5LP_GPIO5JTAG MTDILP_UART TXFSPIWP | affects boot (strapping)not 5 V tolerant | verifiedStrapping (MTDI): together with GPIO4 sets the SDIO slave clock edges. Don't pull it hard at reset.JTAG pins: JTAG goes over USB by default, so these pins are free. |
| 6 | GPIO6 | interruptPWM (LEDC)ADC1_CH6LP_GPIO6JTAG MTCKLP_I2C SDAFSPICLK | not 5 V tolerant | verifiedJTAG pins: JTAG goes over USB by default, so these pins are free. |
| 7 | GPIO7 | interruptPWM (LEDC)LP_GPIO7JTAG MTDOLP_I2C SCLFSPID | not 5 V tolerant | verifiedJTAG pins: JTAG goes over USB by default, so these pins are free. |
| 0 | GPIO0 | interruptPWM (LEDC)ADC1_CH0LP_GPIO0XTAL_32K_PLP_UART DTR | not 5 V tolerant | verified |
| 1 | GPIO1 | interruptPWM (LEDC)ADC1_CH1LP_GPIO1XTAL_32K_NLP_UART DSR | not 5 V tolerant | verified |
| 8 | GPIO8 | interruptPWM (LEDC) | affects boot (strapping)not 5 V tolerantonboard LED | verifiedStrapping: must be high when booting firmware (GPIO9 = 0 selects the download mode). Don't pull it to ground at reset.WS2812B addressable RGB LED on the board (silkscreen RGB@IO8). |
| 10 | GPIO10 | interruptPWM (LEDC) | not 5 V tolerant | verified |
| 11 | GPIO11 | interruptPWM (LEDC) | not 5 V tolerant | verified |
| 2 | GPIO2 | interruptPWM (LEDC)ADC1_CH2LP_GPIO2LP_UART RTSFSPIQ | not 5 V tolerant | verified |
| 3 | GPIO3 | interruptPWM (LEDC)ADC1_CH3LP_GPIO3LP_UART CTS | not 5 V tolerant | verified |
| 5V | 5 V | power inputpower output | verified | |
| G | Ground | verified | ||
| NC | not connected | verified | ||
| G | Ground | verified | ||
| TX | GPIO16 | interruptPWM (LEDC)UART0 TXFSPICS0 | outputs a signal at bootnot 5 V tolerant | verifiedConnected to the CP2102N ("UART" port). |
| RX | GPIO17 | interruptPWM (LEDC)UART0 RXFSPICS1 | not 5 V tolerant | verifiedConnected to the CP2102N ("UART" port). |
| 15 | GPIO15 | interruptPWM (LEDC) | affects boot (strapping)not 5 V tolerant | verifiedStrapping: JTAG source selection. By default it doesn't affect operation as long as the eFuses haven't been touched. |
| 23 | GPIO23 | interruptPWM (LEDC)SDIO_DATA3I2C SDA | not 5 V tolerant | verified |
| 22 | GPIO22 | interruptPWM (LEDC)SDIO_DATA2I2C SCL | not 5 V tolerant | verified |
| 21 | GPIO21 | interruptPWM (LEDC)SDIO_DATA1FSPICS5SPI SCK | not 5 V tolerant | verified |
| 20 | GPIO20 | interruptPWM (LEDC)SDIO_DATA0FSPICS4SPI MISO | not 5 V tolerant | verified |
| 19 | GPIO19 | interruptPWM (LEDC)SDIO_CLKFSPICS3SPI MOSI | not 5 V tolerant | verified |
| 18 | GPIO18 | interruptPWM (LEDC)SDIO_CMDFSPICS2SPI SS | not 5 V tolerant | verified |
| 9 | GPIO9 | interruptPWM (LEDC) | affects boot (strapping)not 5 V tolerantonboard button | verifiedStrapping: low at reset = firmware download mode (BOOT button). Internal pull-up.BOOT button on the board. |
| G | Ground | verified | ||
| 13 | GPIO13 | interruptPWM (LEDC)USB D+ | USB linenot 5 V tolerant | verifiedBuilt-in USB line (Serial/JTAG or OTG). If you use it as GPIO, the port and flashing over this USB disappear.Connected to the board "USB" port (D+). |
| 12 | GPIO12 | interruptPWM (LEDC)USB D− | USB linenot 5 V tolerant | verifiedBuilt-in USB line (Serial/JTAG or OTG). If you use it as GPIO, the port and flashing over this USB disappear.Connected to the board "USB" port (D−). |
| G | Ground | verified | ||
| NC | not connected | verified |
Sources
Every pin is verified against the manufacturer's documents.
- ESP32-C6-DevKitC-1 User Guide (Espressif), Header Block J1/J3user guide, checked 17.10.2026functions of all 32 pins on J1 and J3, RGB LED on GPIO8, two USB-C ports, jumper J5 for current measurement
- ESP32-C6-DevKitC-1 v1.2 dimensions (PDF)board drawing, checked 17.10.2026board 25.40×51.80 mm, rows 22.86 mm apart, 1.27 mm from the edge, bottom pin 12.125 mm from the bottom edge, module 18.00 mm overhangs by 6.35 mm, silkscreen
- ESP32-C6-DevKitC-1 v1.4 schematicschematic, checked 17.10.2026CP2102N, SGM2212-3.3, WS2812B, ESP32-C6-WROOM-1
- ESP32-C6 Series Datasheet (Espressif)datasheet, checked 17.10.2026pin functions: ADC1_CH0–6 on GPIO0–6, LP GPIO0–7, LP_UART and LP_I2C, USB GPIO12/13, UART0 GPIO16/17, JTAG GPIO4–7, SDIO GPIO18–23, flash GPIO24–30
- ESP-IDF: GPIO (ESP32-C6)user guide, checked 17.10.2026strapping GPIO4, 5, 8, 9, 15; flash GPIO24–30; USB-JTAG GPIO12/13; LP GPIO0–7; ADC1_CH0–6 on GPIO0–6
- arduino-esp32: variants/esp32c6/pins_arduino.hArduino core, checked 17.10.2026defaults: TX 16, RX 17, SDA 23, SCL 22, SS 18, MOSI 19, MISO 20, SCK 21, RGB LED 8
Size: per the Espressif dimensional drawing v1.2.
FAQ
- Which ESP32-C6 DevKitC-1 pins are I2C, SPI and UART?
- By default in arduino-esp32 (ESP32C6 Dev Module): I2C: SDA GPIO23, SCL GPIO22; SPI: MOSI GPIO19, MISO GPIO20, SCK GPIO21, SS GPIO18; UART: TX GPIO16, RX GPIO17.
- Which pin is the ESP32-C6 DevKitC-1 LED on?
- WS2812B RGB LED on GPIO8.
- Are the ESP32-C6 DevKitC-1 pins 5 V tolerant?
- No. The logic is 3.3 V and the pins are not 5 V tolerant: use a divider or a level shifter for 5 V signals.
You might also need
Schematic with this board
schematic builder with the board already placed
Flash this board
upload a sketch or .bin to this board from the browser
Power budget
will the regulator cope and how long the battery lasts
Calculators
LED resistor, voltage divider, battery runtime, 3D print cost, LED strip power supply and pF, nF, µF conversion
Similar boards
Next
- Emotion keychainmy ESP32-C5 project, prototype
- ESP32 music playermy ESP32 project, prototype
- DITHR//CAMmy ESP32 project, prototype
Need firmware or a device built on ESP32? I'll build it to order



