MAX17048 pinout
MAX17048, LiPo fuel gauge (Adafruit 5580), Maxim MAX17048, 3.3 V logic, 25.4×20.32 mm, 8 pins
verified17.10.2026
Top view, pin row at the bottom, battery connectors at the top, rotated 90° on the diagram.
Download PNG- Chip
- Maxim MAX17048
- Logic
- 3.3 V
- Power
- VIN 3-5 V
- I2C address
- 0x36
Important
- I2C address 0x36, fixed. Library: Adafruit_MAX1704X.
- One Li-ion or LiPo battery (single cell) in either of the two JST PH connectors; the other goes to the charger or the load.
- Unbranded MAX17048 modules have different labels (VCC, CELL, ALRT, QST) and their own pin order: check against the board.
- Without a battery (or if it's flat) the chip doesn't respond on I2C.
Revisions and clones
- SparkFun Qwiic MAX17048 and unbranded modules: different layout.
- MAX17049 is for two cells in series.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| VIN | 3.3 V | power input | verifiedApply the board's logic level (3.3 or 5 V). | |
| GND | Ground | verified | ||
| SCL | I2C SCL | onboard pull-up | verified10 kΩ pull-up to VIN. | |
| SDA | I2C SDA | onboard pull-up | verified10 kΩ pull-up to VIN. | |
| INT | ALRT: interrupt, low level on alert (low charge, voltage) | onboard pull-up | verifiedPulled up to VIN by 10 kΩ. The threshold is set by a register.Labelled on other revisions as: ALRT, ALERT | |
| QStart | QSTRT: quick restart of the charge estimate (high-level pulse) | verifiedNot used: leave it unconnected (Adafruit doesn't describe a pull).Labelled on other revisions as: QST, QSTRT | ||
| BAT | 3.7 V | power output | verifiedBattery voltage from the JST connector (2.5–4.2 V). There is no label on the front side. | |
| GND | Ground | verified |
Sources
Every pin is verified against the manufacturer's documents.
- Adafruit: Adafruit-MAX17048-STEMMA.brd (Eagle)board drawing, checked 17.10.2026outline 25.4×20.32, row VIN, GND, SCL, SDA, INT, QStart at y 17.78; VBAT and GND pads; two JST PH, two STEMMA QT, holes
- Adafruit Learn: MAX17048 LiPoly / LiIon Fuel Gauge, Pinoutsuser guide, checked 17.10.2026VIN 3–5 V, 10 kΩ pull-ups on SCL, SDA and INT to VIN, address 0x36, JST connectors are interchangeable, Bat is the battery voltage, "on" LED and jumper
- Adafruit: MAX17048 LiPoly / LiIon Fuel Gauge (5580)user guide, checked 17.10.2026the chip is powered from the battery, without it it doesn't respond on I2C
- Maxim MAX17048/MAX17049 datasheet (Mouser copy)datasheet, checked 17.10.2026VDD 2.5–4.5 V, SDA open drain, ALRT is the alert output to an MCU interrupt, QSTRT is quick start (if unused, tie to ground), CELL referenced to GND
Size: per the Eagle outline.
FAQ
- What is the I2C address of the MAX17048?
- 0x36. SDA and SCL pull-ups are on the module.
You might also need
Similar boards

Adafruit Micro-Lipo USB-C LiPo charger (MCP73831, product 4410)
MCP73831T-2ACI/OT7 pins

BMS 1S protection board (3.7 V, DW01 + 8205A)
DW01A + FS8205A4 pins

BMS 2S protection board (7.4 V, with balancing)
2S protection controller (HY2120/HY2213 and equivalents) + MOSFET5 pins

BMS 3S protection board (11.1 V, with balancing)
3S protection controller (HY2120/HY2213 and equivalents) + MOSFET6 pins