MT3608 boost module pinout
MT3608 boost module (36×17, "2 A", trimmer), MT3608, 5 V logic, 36×17 mm, 4 pins
partly verified17.10.2026
Top view, input on the left, output on the right.
BuyDownload PNG- Chip
- MT3608
- Logic
- 5 V
- Power
- VIN+ 2-24 V
Important
- The output is adjustable: the builder and the circuit check assume 5 V. Set it with the trimmer before connecting the board, with no load, using a multimeter.
- A boost converter does not step down: if the input is above the set output, the output will be the input minus 0.3-0.5 V (through a diode). 9 V in with 5 V set gives about 8.6 V out.
- With no load it draws about 1 mA: that is a lot for long battery sleep (720 mAh per month), better to switch it off.
- Output ripple up to 0.5 V: for ESP32 and radio add 100-470 µF on the output.
- From Li-ion 3.7 V to 5 V: up to 1 A continuous on the output, about 1.5 A from the battery.
- Geometry from seller descriptions (±0.5 mm), components drawn approximately. Check with calipers before laying out your own board.
- Output 5-28 V by the trimmer (5 V in the data).
Revisions and clones
- Modules with micro-USB on the input (MT3608 + connector): same VOUT±.
- Some are labeled OUT+/OUT− instead of VOUT+/VOUT−.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| VIN+ | 3.7 V | power input | not verifiedWhich of the two end pads is "+" and which is "−" is not verified against the descriptions found: read the labels on the board.Labelled on other revisions as: IN+ | |
| VIN- | Ground | not verifiedWhich of the two end pads is "+" and which is "−" is not verified against the descriptions found: read the labels on the board.Common negative of input and output (connected on the board). | ||
| VOUT+ | 5 V | power output | not verifiedWhich of the two end pads is "+" and which is "−" is not verified against the descriptions found: read the labels on the board.Output 5-28 V (5 V in the circuit check). Continuous up to 1 A, less at a 3-4x boost. | |
| VOUT- | Ground | not verifiedWhich of the two end pads is "+" and which is "−" is not verified against the descriptions found: read the labels on the board. |
Sources
Not verified against the manufacturer: 4 of 4 pins. The pin card says what confirms each one and where sources disagree.
- Aerosemi MT3608 datasheet (Olimex copy)datasheet, checked 17.10.2026input 2-24 V, output up to 28 V, 1.2 MHz, 4 A switch, efficiency up to 97 %
- ProtoSupplies: MT3608 Mini Adjustable DC-DC Boost Modulethird-party source, checked 17.10.2026pads VIN+, VIN−, OUT+, OUT− (negatives are common), 37×17×7, 1 A continuous, 1.5 A peak, no-load current about 1 mA, ripple about 0.5 V without an extra capacitor
- Components101: MT3608 2A DC-DC Step Up Power Modulethird-party source, checked 17.10.2026VIN+, VIN−, VOUT+, VOUT−, 36×17 mm
Size: 36×17 mm from sellers, 37×17×7 at ProtoSupplies (approximate).
You might also need
Similar boards

Boost module 0.9–5 V → 5 V with a USB socket (600 mA)
unmarked (boost controller, SOT-23)4 pins

DD4012SA mini buck module, 3.3 V (up to 1 A, 3 pins)
unmarked (controller in SOT-23-6)3 pins

DD4012SA mini buck module for 5 V (up to 1 A, 3 pins)
unmarked (controller in SOT-23-6)3 pins

LM2596 buck module (blue 43×21, trimmer, up to 2-3 A)
LM2596S-ADJ4 pins