LM2596 buck module pinout
LM2596 buck module (blue 43×21, trimmer, up to 2-3 A), LM2596S-ADJ, 5 V logic, 43×21 mm, 4 pins
partly verified17.10.2026
Top view, input on the left, output on the right.
BuyDownload PNG- Chip
- LM2596S-ADJ
- Logic
- 5 V
- Power
- IN+ 6.5-40 V
Important
- The output is adjustable: the builder and the circuit check assume 5 V. Set it with the trimmer before connecting the board, with no load, using a multimeter.
- The input must be at least 1.5-2 V above the output: you cannot get 3.3 V from a single Li-ion cell.
- Efficiency 80-90%: from 12 V to 5 V at 1 A, the input draws about 0.5 A. Quiescent current is about 5-10 mA, which is a lot for battery sleep.
- Many modules use LM2596 clones: they hold 1-1.5 A and run hot. Output ripple is tens of mV.
- Geometry from seller descriptions (±0.5 mm), components drawn approximately. Check with calipers before laying out your own board.
- Output 1.25-35 V set with the trimmer, 2 A continuous, 3 A with a heatsink.
Revisions and clones
- With a digital voltmeter and a button (larger, 66×36): same IN±/OUT±.
- Fixed LM2596-5.0 and -3.3 have no trimmer.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| IN+ | 12 V | power input | not verifiedWhich of the two end pads is "+" and which is "−" is not verified against the descriptions found: read the labels on the board. | |
| IN- | Ground | not verifiedWhich of the two end pads is "+" and which is "−" is not verified against the descriptions found: read the labels on the board.Common negative of input and output (connected on the board). | ||
| OUT+ | 5 V | power output | not verifiedWhich of the two end pads is "+" and which is "−" is not verified against the descriptions found: read the labels on the board.Output 1.25-35 V (5 V in the circuit check). Up to 2 A without a heatsink. | |
| OUT- | Ground | not verifiedWhich of the two end pads is "+" and which is "−" is not verified against the descriptions found: read the labels on the board. |
Sources
Not verified against the manufacturer: 4 of 4 pins. The pin card says what confirms each one and where sources disagree.
- TI LM2596 SIMPLE SWITCHER 3-A Step-Down Voltage Regulatordatasheet, checked 17.10.2026input up to 40 V, current up to 3 A, 150 kHz, output from 1.23 V, efficiency 73-90% depending on voltages
- KAmod LM2596: 3A Step-down DC-DC Converter Module (Kamami)third-party source, checked 17.10.2026IN+, IN-, OUT+, OUT-; input 3-40 V, output 1.5-35 V, up to 3 A with cooling, efficiency up to 92%, 43×21×14, Ø3 holes
Size: 43×21×14 mm per KAmod and sellers; Ø3 mm holes (approximate).
You might also need
Similar boards

Boost module 0.9–5 V → 5 V with a USB socket (600 mA)
unmarked (boost controller, SOT-23)4 pins

DD4012SA mini buck module, 3.3 V (up to 1 A, 3 pins)
unmarked (controller in SOT-23-6)3 pins

DD4012SA mini buck module for 5 V (up to 1 A, 3 pins)
unmarked (controller in SOT-23-6)3 pins

MP1584EN mini step-down module (22×17, 1.5–3 A)
MP1584EN4 pins