MP1584EN mini step-down module pinout
MP1584EN mini step-down module (22×17, 1.5–3 A), MP1584EN, 5 V logic, 22×17 mm, 4 pins
partly verified17.10.2026
Top view, input on the left, output on the right.
Download PNG- Chip
- MP1584EN
- Logic
- 5 V
- Power
- IN+ 6.6-28 V
Important
- The output is adjustable: the builder and the circuit check assume 5 V. Set it with the trimmer before connecting the board, with no load, using a multimeter.
- Small and high-frequency: good for 12 V → 5 V in a car and from 2S–3S batteries. Doesn't work from a single Li-ion cell (input starts at 4.5 V).
- The single-turn trimmer is easy to knock off: after adjusting, seal it with varnish or a drop of glue.
- Geometry from seller descriptions (±0.5 mm), components drawn approximately. Check with calipers before laying out your own board.
- About 1.5 A continuous without overheating, peaks up to 2–3 A.
Revisions and clones
- Fixed versions for 3.3, 5, 9, 12 V: a resistor instead of the trimmer, output marked on the board.
- "Mini-360" (MP2307, 17×11 mm) is a different module, input up to 23 V, current up to 1.8 A.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| IN+ | 12 V | power input | not verifiedWhich of the two end pads is "+" and which is "−" is not verified against the descriptions found: read the labels on the board. | |
| IN- | Ground | not verifiedWhich of the two end pads is "+" and which is "−" is not verified against the descriptions found: read the labels on the board.Common negative of input and output (connected on the board). | ||
| OUT+ | 5 V | power output | not verifiedWhich of the two end pads is "+" and which is "−" is not verified against the descriptions found: read the labels on the board.Output 0.8–20 V (5 V in the circuit check). Up to 1.5 A continuous. | |
| OUT- | Ground | not verifiedWhich of the two end pads is "+" and which is "−" is not verified against the descriptions found: read the labels on the board. |
Sources
Not verified against the manufacturer: 4 of 4 pins. The pin card says what confirms each one and where sources disagree.
- MPS MP1584 product page and datasheetdatasheet, checked 17.10.2026input 4.5–28 V, 3 A, 1.5 MHz, output from 0.8 V
- Eckstein: Mini DC-DC Step Down MP1584EN 0,8–20 V 3 Athird-party source, checked 17.10.202622×17×4 mm, input 4.5–28 V, output 0.8–20 V, 3 A
- ProtoSupplies: MP1584 Mini Adjustable DC-DC Step-Down Modulethird-party source, checked 17.10.2026IN+, IN−, OUT+, OUT−; up to 1.5 A continuous, peaks 2 A; drop about 1.6 V; clockwise lowers the output
Size: 22×17×4 mm per sellers (approximate).
You might also need
Similar boards

Boost module 0.9–5 V → 5 V with a USB socket (600 mA)
unmarked (boost controller, SOT-23)4 pins

DD4012SA mini buck module, 3.3 V (up to 1 A, 3 pins)
unmarked (controller in SOT-23-6)3 pins

DD4012SA mini buck module for 5 V (up to 1 A, 3 pins)
unmarked (controller in SOT-23-6)3 pins

LM2596 buck module (blue 43×21, trimmer, up to 2-3 A)
LM2596S-ADJ4 pins