RFID reader RC522 pinout
RFID reader RC522 (MFRC522, 13.56 MHz, SPI), NXP MFRC522, 3.3 V logic, 40×60 mm, 8 pins
partly verified20.10.2026
Component side view, antenna at the top, header at the bottom: SDA, SCK, MOSI, MISO, IRQ, GND, RST, 3.3V from left to right.
Download PNG- Chip
- NXP MFRC522
- Logic
- 3.3 V
- Power
- 3.3V 2.5-3.6 V
Important
- 3.3 V supply only: at 5 V the module burns out. The builder raises an error if 3.3V is connected to 5 V.
- To ESP32 (VSPI): SDA to GPIO5, SCK to GPIO18, MOSI to GPIO23, MISO to GPIO19, RST to any GPIO (for example 22), 3.3V to 3V3. MFRC522 library (miguelbalboa).
- To Arduino Uno: SDA D10, SCK D13, MOSI D11, MISO D12, RST D9, 3.3V to 3.3V. Uno signals are 5 V: per NXP an input must not exceed 3.3 + 0.5 V, so SDA, SCK, MOSI and RST are better connected through a divider or level shifter. Many people connect directly and report that it works: the builder flags such wires as an error per the datasheet.
- The MFRC522 library does not need IRQ: leave it unconnected.
- A card reads at 3-5 cm. Metal under or next to the antenna reduces the range.
- The module draws 13-26 mA while reading (lastminuteengineers), the chip transmitter up to 100 mA at the limit (NXP).
Revisions and clones
- RC522 Mini modules and ones with a 2×4 header: different pin order, check the silkscreen.
- PN532: a different chip (NFC, I2C/SPI/UART), different pins.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| SDA | SPI SS (CS): chip select, active low | not 5 V tolerant | not from manufacturerModule without a manufacturer: the pin order follows two guides (they agree), there is no board manufacturer document. Check the silkscreen on your board.This is the SPI select pin (SS), unrelated to I2C: the MFRC522 on the module is set to SPI mode.Labelled on other revisions as: SS, CS, NSS | |
| SCK | SPI SCK | not 5 V tolerant | not from manufacturerModule without a manufacturer: the pin order follows two guides (they agree), there is no board manufacturer document. Check the silkscreen on your board. | |
| MOSI | SPI MOSI | not 5 V tolerant | not from manufacturerModule without a manufacturer: the pin order follows two guides (they agree), there is no board manufacturer document. Check the silkscreen on your board. | |
| MISO | SPI MISO | not from manufacturerModule without a manufacturer: the pin order follows two guides (they agree), there is no board manufacturer document. Check the silkscreen on your board.Labelled on other revisions as: SCL, TX | ||
| IRQ | IRQ: interrupt on a card or end of command (not needed by the MFRC522 library) | not from manufacturerModule without a manufacturer: the pin order follows two guides (they agree), there is no board manufacturer document. Check the silkscreen on your board. | ||
| GND | Ground | not from manufacturerModule without a manufacturer: the pin order follows two guides (they agree), there is no board manufacturer document. Check the silkscreen on your board. | ||
| RST | NRSTPD: LOW resets and powers down the chip | not 5 V tolerant | not from manufacturerModule without a manufacturer: the pin order follows two guides (they agree), there is no board manufacturer document. Check the silkscreen on your board.Labelled on other revisions as: RESET, NRSTPD | |
| 3.3V | 3.3 V | power input | not from manufacturerModule without a manufacturer: the pin order follows two guides (they agree), there is no board manufacturer document. Check the silkscreen on your board.3.3 V only. At 5 V the chip exceeds its 4.0 V limit (NXP) and burns out.Labelled on other revisions as: VCC, 3V3 |
Sources
Not verified against the manufacturer: 8 of 8 pins. The pin card says what confirms each one and where sources disagree.
- NXP MFRC522 Standard performance MIFARE and NTAG frontend (Rev. 3.9, 27.04.2016)datasheet, checked 20.10.2026supply VDDA, VDDD, TVDD 2.5-3.6 V (typ. 3.3), limit 4.0 V; input on any pin no higher than PVDD + 0.5 V; SPI up to 10 Mbit/s; digital current 6.5-9 mA, analog 7-10 mA, transmitter up to 100 mA in continuous wave; hard power-down by NRSTPD = LOW down to 5 µA
- Random Nerd Tutorials: Security Access using MFRC522 RFID Reader with Arduinothird-party source, checked 20.10.2026pins SDA, SCK, MOSI, MISO, IRQ, GND, RST, 3.3V; to Uno: SDA D10, SCK D13, MOSI D11, MISO D12, RST D9, IRQ not connected; 3.3 V supply only
- Last Minute Engineers: How RC522 RFID Reader Module Worksthird-party source, checked 20.10.2026supply 2.5-3.3 V, current 13-26 mA, 10 µA in power-down; sources say the logic pins tolerate 5 V (NXP: input no higher than PVDD + 0.5 V)
Size: 40×60 mm at sellers; parts and antenna from the photo, not dimensioned (approximate).
FAQ
- What supply voltage does the RFID reader RC522 need?
- 3.3V: 2.5-3.6 V. 3.3 V logic.



