1-channel 5 V relay module without optocoupler pinout
1-channel 5 V relay module without optocoupler (KY-019, triggers on HIGH), Songle SRD-05VDC-SL-C relay, 5 V logic, 34×27 mm, 6 pins
partly verified15.10.2026
Top view, control on the left, terminal block on the right.
Download PNG- Chip
- Songle SRD-05VDC-SL-C relay
- Logic
- 5 V
- Power
- + 4.75-5.25 V
Important
- The relay turns on with a high level on S (HIGH), unlike modules with an optocoupler.
- No isolation: the coil and the MCU share ground, relay noise gets into the MCU supply. For heavy loads a module with an optocoupler is better.
- 220 V mains on the terminal block is lethally dangerous: the module has no enclosure and the trace spacing is small. Keep the contact current under 5 A.
- Geometry from third-party KiCad footprints and seller descriptions (±0.5 mm), small components are drawn approximately. Check with calipers before laying out your own board.
Revisions and clones
- Module with an optocoupler and JD-VCC (turns on at LOW): entry relay-module-1ch-5v-opto.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| S | not from manufacturerNo-name module: the order S, +, − is from Joy-IT and the kit description (they agree); Components101 has a different order (Trigger, GND, VCC): check the labels. Geometry is approximate, no footprint.Through a resistor to the transistor base: a 3.3 V MCU usually switches the relay on, but with less margin.Labelled on other revisions as: SIG, IN | |||
| + | 5 V | power input | not from manufacturerNo-name module: the order S, +, − is from Joy-IT and the kit description (they agree); Components101 has a different order (Trigger, GND, VCC): check the labels. Geometry is approximate, no footprint.Labelled on other revisions as: VCC | |
| - | Ground | not from manufacturerNo-name module: the order S, +, − is from Joy-IT and the kit description (they agree); Components101 has a different order (Trigger, GND, VCC): check the labels. Geometry is approximate, no footprint.Labelled on other revisions as: GND, − | ||
| NO | Normally open: closes with COM when the relay turns on | not verifiedCOM is always in the middle, while NO and NC at the edges are placed differently on different boards. Check the labels at the terminal block (or buzz it out: NC is connected to COM while the relay is off). | ||
| COM | Relay common contact | not from manufacturerNo-name module: the order S, +, − is from Joy-IT and the kit description (they agree); Components101 has a different order (Trigger, GND, VCC): check the labels. Geometry is approximate, no footprint.Up to 10 A 250 V~ / 10 A 30 V= per the relay datasheet; the module traces and terminal block are usually not rated for that current. | ||
| NC | Normally closed: connected to COM while the relay is off | not verifiedCOM is always in the middle, while NO and NC at the edges are placed differently on different boards. Check the labels at the terminal block (or buzz it out: NC is connected to COM while the relay is off). |
Sources
Not verified against the manufacturer: 6 of 6 pins. The pin card says what confirms each one and where sources disagree.
- Songle SRD series relay datasheetdatasheet, checked 15.10.2026SRD-05VDC-SL-C: 5 V coil, 70 Ω, 71.4 mA, 0.36 W; SPDT contacts 10 A 250 V~ / 10 A 30 V=; pull-in at no more than 75% of rated voltage
- Joy-IT SensorKit: KY-019 relay modulethird-party source, checked 15.10.2026pins S, +, −, triggers on high level, 10 A 250 V~
- 45-in-1 sensor kit docs: relay modulethird-party source, checked 15.10.2026S, +, −, active HIGH, NPN transistor and diode
- Components101: 5V single channel relay modulethird-party source, checked 15.10.2026version without optocoupler with active high level, 5 V supply, Trigger, GND, VCC, NO, COM, NC
Size: 34×27 mm at most sellers; Joy-IT lists 26×38 (approximate).
FAQ
- What supply voltage does the 1-channel 5 V relay module without optocoupler need?
- +: 4.75-5.25 V. 5 V logic.
You might also need
Similar boards

1-channel 5 V relay module with optocoupler (active LOW, JD-VCC jumper)
Songle SRD-05VDC-SL-C relay + PC817 optocoupler8 pins

A4988 stepper motor driver (StepStick, Pololu and clones)
Allegro A498816 pins

DRV8825 stepper motor driver (StepStick, Pololu and clones)
TI DRV882516 pins

DRV8833, dual motor driver (HW-627 module, 12 pins)
TI DRV883312 pins