2.0" IPS display 240×320 ST7789 pinout
2.0" IPS display 240×320 ST7789, SPI (8 pins), Sitronix ST7789V, 3.3 V logic, 36.48×61.12 mm, 8 pins
partly verified17.10.2026
Front view (screen side), connector at the top.
Download PNG- Chip
- Sitronix ST7789V
- Logic
- 3.3 V
- Power
- VCC 3-3.6 V
Important
- SCL and SDA on the board are SPI (SCK and MOSI), not I2C. CS, DC and RES can go to any GPIO.
- Power and logic are 3.3 V. With a 5 V Arduino: level shifter on SCL, SDA, RES, DC, CS.
- Libraries: TFT_eSPI (ST7789_DRIVER, 240×320), Adafruit_ST7789, LovyanGFX.
- Board size per the module manufacturer; connector and glass position from the photo (±1 mm), not measured.
Revisions and clones
- Modules with 7 pins (no CS) are for 240×240: a different module.
- The Waveshare 2inch LCD has a PH2.0 connector and labels DIN, CLK, RST, BL; the DFRobot DFR0664 also has MISO and SDCS for a card.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| GND | Ground | not from manufacturerPin order per Elecrow, but similar no-name modules may have a different order, a BL label instead of BLK and a regulator for 5 V. The connector position is not dimensioned. | ||
| VCC | 3.3 V | power input | not from manufacturerPin order per Elecrow, but similar no-name modules may have a different order, a BL label instead of BLK and a regulator for 5 V. The connector position is not dimensioned. | |
| SCL | SPI SCK (labeled SCL on the board) | not 5 V tolerant | not from manufacturerPin order per Elecrow, but similar no-name modules may have a different order, a BL label instead of BLK and a regulator for 5 V. The connector position is not dimensioned.This is SPI, not I2C: connect to the board SCK. | |
| SDA | SPI MOSI (labeled SDA on the board) | not 5 V tolerant | not from manufacturerPin order per Elecrow, but similar no-name modules may have a different order, a BL label instead of BLK and a regulator for 5 V. The connector position is not dimensioned.This is SPI, not I2C: connect to the board MOSI. The module has no MISO. | |
| RES | Reset, active low | not 5 V tolerant | not from manufacturerPin order per Elecrow, but similar no-name modules may have a different order, a BL label instead of BLK and a regulator for 5 V. The connector position is not dimensioned.Labelled on other revisions as: RST, RESET | |
| DC | D/C: low = command, high = data | not 5 V tolerant | not from manufacturerPin order per Elecrow, but similar no-name modules may have a different order, a BL label instead of BLK and a regulator for 5 V. The connector position is not dimensioned.Labelled on other revisions as: RS, A0 | |
| CS | SPI CS, active low | not 5 V tolerant | not from manufacturerPin order per Elecrow, but similar no-name modules may have a different order, a BL label instead of BLK and a regulator for 5 V. The connector position is not dimensioned. | |
| BLK | Backlight: high = on, brightness by PWM | not 5 V tolerant | not from manufacturerPin order per Elecrow, but similar no-name modules may have a different order, a BL label instead of BLK and a regulator for 5 V. The connector position is not dimensioned.If you do not control it, connect to 3.3 V.Labelled on other revisions as: BL, LED |
Sources
Not verified against the manufacturer: 8 of 8 pins. The pin card says what confirms each one and where sources disagree.
- Elecrow Wiki: 2 inch IPS Moduleuser guide, checked 17.10.2026order GND, VCC, SCL, SDA, RES, DC, CS, BLK; 3.3 V supply; board 36.48×61.12; active area 30.60×40.80; ST7789 controller
- Sitronix ST7789V datasheet (Newhaven copy)datasheet, checked 17.10.20264-wire SPI: SCL, SDA, CSX, D/CX (low = command), RESX active low, logic supply 1.65-3.3 V
- KiCad: Jana-Marie/KiCAD-libs 2.0Inch-IPS-ST7789third-party source, checked 17.10.20262.0" ST7789 panel: glass 35.7×51.2 mm
Size: 36.48×61.12 per Elecrow; Waveshare 35×58, DFRobot 35.7×60 (approximate).
FAQ
- What supply voltage does the 2.0" IPS display 240×320 ST7789 need?
- VCC: 3-3.6 V. 3.3 V logic.



