TPA6132A2 headphone amplifier pinout
TPA6132A2 headphone amplifier (generic board from the TI datasheet), TI TPA6132A2, 3.3 V logic, 33.02×12.7 mm, 12 pins
draft17.10.2026
- INL-Left input, inverting
- INL+Left input…
- INR+Right input…
- INR-Right input, inverting
- G0Gain, bit 0
- G1Gain, bit 1
- ENEnable
- VDD2.3-5.5 V
- GND
- SGND
- OUTLHeadphone output, left
- OUTRHeadphone output…
Top view, 12-pin row at the bottom, rotated 90° on the diagram.
Download PNG- Chip
- TI TPA6132A2
- Logic
- 3.3 V
- Power
- VDD 2.3-5.5 V
Important
- This is a generic breakout for the builder: pin functions are checked against the datasheet, the layout is not taken from a real module.
- DirectPath: outputs are centered on 0 V, connect headphones without capacitors, sleeve of the jack to SGND.
- The input is single-ended: signal to INL− and INR−, INL+ and INR+ to ground. The chip has no volume control.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| INL- | Left input, inverting: single-ended signal goes here | not verifiedNo mass-market module with the TPA6132A2 was found (only the TI evaluation board). Pin functions are from the TI datasheet; header order and board size are generic, check against the board in hand.Through a coupling capacitor if the source has a bias. | ||
| INL+ | Left input, non-inverting: to ground for a single-ended signal | not verifiedNo mass-market module with the TPA6132A2 was found (only the TI evaluation board). Pin functions are from the TI datasheet; header order and board size are generic, check against the board in hand. | ||
| INR+ | Right input, non-inverting: to ground for a single-ended signal | not verifiedNo mass-market module with the TPA6132A2 was found (only the TI evaluation board). Pin functions are from the TI datasheet; header order and board size are generic, check against the board in hand. | ||
| INR- | Right input, inverting: single-ended signal goes here | not verifiedNo mass-market module with the TPA6132A2 was found (only the TI evaluation board). Pin functions are from the TI datasheet; header order and board size are generic, check against the board in hand. | ||
| G0 | Gain, bit 0 | not verifiedNo mass-market module with the TPA6132A2 was found (only the TI evaluation board). Pin functions are from the TI datasheet; header order and board size are generic, check against the board in hand. | ||
| G1 | Gain, bit 1 | not verifiedNo mass-market module with the TPA6132A2 was found (only the TI evaluation board). Pin functions are from the TI datasheet; header order and board size are generic, check against the board in hand.G0 and G1 (low ≤ 0.5 V, high ≥ 1.3 V): 00 −6 dB, G0=1 0 dB, G1=1 3 dB, both 6 dB. | ||
| EN | Enable: high = on, low = shutdown (< 1 µA) | not verifiedNo mass-market module with the TPA6132A2 was found (only the TI evaluation board). Pin functions are from the TI datasheet; header order and board size are generic, check against the board in hand. | ||
| VDD | 3.3 V | power input | not verifiedNo mass-market module with the TPA6132A2 was found (only the TI evaluation board). Pin functions are from the TI datasheet; header order and board size are generic, check against the board in hand. | |
| GND | Ground | not verifiedNo mass-market module with the TPA6132A2 was found (only the TI evaluation board). Pin functions are from the TI datasheet; header order and board size are generic, check against the board in hand. | ||
| SGND | Ground | not verifiedNo mass-market module with the TPA6132A2 was found (only the TI evaluation board). Pin functions are from the TI datasheet; header order and board size are generic, check against the board in hand.Amplifier reference ground: connect to the common pin (sleeve) of the headphone jack. | ||
| OUTL | Headphone output, left (centered on zero) | not verifiedNo mass-market module with the TPA6132A2 was found (only the TI evaluation board). Pin functions are from the TI datasheet; header order and board size are generic, check against the board in hand.16-32 Ω headphones directly, no capacitor. | ||
| OUTR | Headphone output, right (centered on zero) | not verifiedNo mass-market module with the TPA6132A2 was found (only the TI evaluation board). Pin functions are from the TI datasheet; header order and board size are generic, check against the board in hand. |
Sources
Not verified against the manufacturer: 12 of 12 pins. The pin card says what confirms each one and where sources disagree.
- TI TPA6132A2 datasheet (SLOS597B)datasheet, checked 17.10.2026pins INL±, INR±, G0, G1, EN, VDD, SGND, OUTL, OUTR, HPVDD, HPVSS, CPP, CPN; supply 2.3-5.5 V, current 2.1 mA, shutdown < 1 µA, gain table, 25 mW into 16 Ω
- TI TPA6132A2EVM2 (evaluation board)user guide, checked 17.10.2026the only board with this chip that was found: the TI evaluation board, supply 2.5-5.5 V
Size: generic breakout: chip pins 1:1 in a row, support parts from the datasheet (approximate).
FAQ
- What supply voltage does the TPA6132A2 headphone amplifier need?
- VDD: 2.3-5.5 V. 3.3 V logic.



