USB-C power-only breakout pinout
USB-C power-only breakout (6P connector, VBUS and GND, 5.1 kΩ resistors), USB Type-C 6P socket (VBUS ×2, GND ×2, CC1, CC2), 5 V logic, 12×10 mm, 2 pins
partly verified17.10.2026
Top view, USB-C socket at the top, pads at the bottom.
BuyDownload PNG- Chip
- USB Type-C 6P socket (VBUS ×2, GND ×2, CC1, CC2)
- Logic
- 5 V
- Power
- USB-C 4.75-5.25 V
Important
- Check the resistors: the board should have two "512" resistors (5.1 kΩ) at CC1 and CC2. Without them a USB-A to USB-C cable works, but a C-C cable from a USB-C charger doesn't (0 V).
- A 2P connector (only VBUS and GND, no CC) gets no power from USB-C chargers at all: it works only with a USB-A to USB-C cable.
- Current: with 5.1 kΩ resistors a charger gives up to 1.5–3 A, a computer port 500–900 mA. The 6P connector is rated for 3–5 A.
- 5 V from USB. A USB-C source (charger, power bank, laptop) enables VBUS only if 5.1 kΩ resistors from CC1 and CC2 to ground are present.
Revisions and clones
- 2P: the same without CC, doesn't work from C-C.
- The breakout with data lines (16P, D+/D-) is the entry usb-c-breakout-16p.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| VBUS | 5 V | power output | not verifiedUnbranded adapter: labels and pad order differ between boards and are not verified. Read the labels on your board.5 V from USB. A USB-C source (charger, power bank, laptop) enables VBUS only if 5.1 kΩ resistors from CC1 and CC2 to ground are present.Labelled on other revisions as: VCC, V+, 5V, + | |
| GND | Ground | not verifiedUnbranded adapter: labels and pad order differ between boards and are not verified. Read the labels on your board.Labelled on other revisions as: V-, - |
Sources
Not verified against the manufacturer: 2 of 2 pins. The pin card says what confirms each one and where sources disagree.
- USB Type-C Cable and Connector Specification (USB-IF), Rd 5.1 kΩ on CC on the consumer sidedatasheet, checked 17.10.2026the consumer (Sink) places Rd 5.1 kΩ from CC1 and CC2 to ground, without it a USB-C source does not enable VBUS; D+/D− as in USB 2.0
- combs/USBC6P: breakout on a USB-C 6P connectorthird-party source, checked 17.10.20266P connector: only VBUS, GND, CC1, CC2, no D+/D-; 5.1 kΩ on CC gives 5 V without negotiation
Size: no dimensions given, about 12×10 mm (approximate).
You might also need
Similar boards

USB-C 16P breakout to pins (VBUS, GND, CC1, CC2, D+, D−)
USB Type-C 16P receptacle (USB 2.0)6 pins

Adafruit Micro-Lipo USB-C LiPo charger (MCP73831, product 4410)
MCP73831T-2ACI/OT7 pins

BMS 1S protection board (3.7 V, DW01 + 8205A)
DW01A + FS8205A4 pins

BMS 2S protection board (7.4 V, with balancing)
2S protection controller (HY2120/HY2213 and equivalents) + MOSFET5 pins