Seeed XIAO ESP32C3 pinout
Seeed XIAO ESP32C3, ESP32-C3, 3.3 V logic, 17.8×20.975 mm, 14 pins
verified17.10.2026
- D0GPIO22BOOTFSPIQADC1_CH2wake from deep sleep
- D1GPIO33ADC1_CH3wake from deep sleep
- D2GPIO44FSPIHDADC1_CH4wake from deep sleepJTAG MTMS
- D3GPIO55FSPIWPADC2_CH0wake from deep sleepJTAG MTDI
- D4GPIO66I2C SDAFSPICLKJTAG MTCK
- D5GPIO77I2C SCLFSPIDJTAG MTDO
- D6GPIO2121BOOTUART0 TXSerial1 TX
Top view, USB-C at the top.
CompareDownload PNG- Chip
- ESP32-C3, ESP32-C3 + 4 MB flash
- Logic
- 3.3 V
- Power
- USB-C 4.75-5.25 V5V 4.75-5.25 VLi-ion 3.7 V (BAT+ and BAT− pads on the back) 3.3-4.2 V
- Defaults in arduino-esp32 (XIAO_ESP32C3)
- I2C: SDA 6, SCL 7SPI: MOSI 10, MISO 9, SCK 8, SS 20UART: TX 21, RX 20
Which Seeed XIAO ESP32C3 pins are safe to use
Free to use
GPIO3-7, GPIO10, GPIO20
Use with care
- GPIO2, GPIO8, GPIO9: strapping: the level at power-up selects the boot mode.
- GPIO21: signal at boot.
Important
- 3.3 V logic, don't put 5 V on the GPIO.
- The labels D0…D10, 5V, GND, 3V3 are printed on the back (the screen is on top), the Arduino numbers are D0…D10, not GPIO.
- There is no user LED (LED_BUILTIN is not defined), only the charge LED.
- Strapping pins on the header: D0 (GPIO2), D8 (GPIO8), D9 (GPIO9, BOOT button). Modules on them can interfere with flashing and startup.
- ADC: D0–D2 (ADC1). D3 (GPIO5) is ADC2, which is unreliable per the ESP32-C3 errata.
- In the core variant SS = GPIO20 (this is D7, RX): for SPI choose CS manually.
- Placement of small components is approximate, pins and size follow the Seeed footprint.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| D0 | GPIO2, Arduino D0 (2) | interruptPWM (LEDC)ADC1_CH2wake from deep sleep (deep sleep GPIO)FSPIQ | not 5 V tolerantaffects boot (strapping) | verifiedStrapping: floating by default, Espressif recommends a pull-up. Do not pull low at reset. |
| D1 | GPIO3, Arduino D1 (3) | interruptPWM (LEDC)ADC1_CH3wake from deep sleep (deep sleep GPIO) | not 5 V tolerant | verified |
| D2 | GPIO4, Arduino D2 (4) | interruptPWM (LEDC)ADC1_CH4wake from deep sleep (deep sleep GPIO)JTAG MTMSFSPIHD | not 5 V tolerant | verifiedJTAG pins: JTAG goes over USB by default, so these pins are free. |
| D3 | GPIO5, Arduino D3 (5) | interruptPWM (LEDC)ADC2_CH0wake from deep sleep (deep sleep GPIO)JTAG MTDIFSPIWP | not 5 V tolerantADC2 doesn't work with Wi-Fi on | verifiedADC2 on the ESP32-C3 gives wrong results per the errata, ESP-IDF does not recommend it. For the ADC use GPIO0–4.JTAG pins: JTAG goes over USB by default, so these pins are free. |
| D4 | GPIO6, Arduino D4 (6) | interruptPWM (LEDC)JTAG MTCKFSPICLKI2C SDA | not 5 V tolerant | verifiedJTAG pins: JTAG goes over USB by default, so these pins are free. |
| D5 | GPIO7, Arduino D5 (7) | interruptPWM (LEDC)JTAG MTDOFSPIDI2C SCL | not 5 V tolerant | verifiedJTAG pins: JTAG goes over USB by default, so these pins are free. |
| D6 | GPIO21, Arduino D6 (21) | interruptPWM (LEDC)UART0 TXSerial1 TX | not 5 V tolerantoutputs a signal at boot | verified |
| 5V | 5 V | power inputpower output | verified5 V from USB-C (output) or a 5 V input. Nothing here when running from a battery. | |
| GND | Ground | verified | ||
| 3V3 | 3.3 V | power output | verifiedBoard 3.3 V regulator output. | |
| D10 | GPIO10, Arduino D10 (10) | interruptPWM (LEDC)FSPICS0SPI MOSI | not 5 V tolerant | verified |
| D9 | GPIO9, Arduino D9 (9) | interruptPWM (LEDC)SPI MISO | not 5 V tolerantaffects boot (strapping) | verifiedStrapping: low at reset = firmware download mode (BOOT button). Internal pull-up. |
| D8 | GPIO8, Arduino D8 (8) | interruptPWM (LEDC)SPI SCK | not 5 V tolerantaffects boot (strapping) | verifiedStrapping: must be high for firmware download mode (GPIO9 = 0), also controls ROM message output. Do not pull low at reset. |
| D7 | GPIO20, Arduino D7 (20) | interruptPWM (LEDC)UART0 RXSerial1 RXSPI SS | not 5 V tolerant | verified |
Sources
Every pin is verified against the manufacturer's documents.
- Seeed Studio Wiki: Getting Started with Seeed XIAO ESP32C3user guide, checked 17.10.2026D0–D10 → GPIO2, 3, 4, 5, 6, 7, 21, 20, 8, 9, 10; strapping GPIO2, 8, 9; no user LED; BOOT button (GPIO9); charging 380 mA; sleep 44 µA; 21×17.8 mm
- Seeed OPL_Kicad_Library: XIAO-ESP32-C3-DIP.kicad_modboard drawing, checked 17.10.202614 pins: two rows 15.24 mm apart, pitch 2.54, outline 20.975×17.8 mm, outermost pin 2.93 mm from the USB edge
- arduino-esp32: variants/XIAO_ESP32C3/pins_arduino.hArduino core, checked 17.10.2026D0–D10, TX 21, RX 20, SDA 6, SCL 7, SS 20, MOSI 10, MISO 9, SCK 8
- ESP32-C3 Series Datasheet (Espressif)datasheet, checked 15.10.2026pin functions, ADC1_CH0–4 on GPIO0–4, ADC2_CH0 on GPIO5, strapping GPIO2/8/9, USB D−/D+ on GPIO18/19, UART0 on GPIO20/21, JTAG GPIO4–7
- ESP-IDF: GPIO (ESP32-C3)user guide, checked 15.10.2026GPIO12–17 used by SPI flash, strapping pins, GPIO18/19 USB, deep sleep wake-up on GPIO0–5
- arduino-esp32: variants/esp32c3 and nologo_esp32c3_super_mini/pins_arduino.hArduino core, checked 15.10.2026defaults: TX 21, RX 20, SDA 8, SCL 9, SS 7, MOSI 6, MISO 5, SCK 4, LED_BUILTIN 8 (SuperMini)
- ESP32-C3 Series SoC Erratachip errata, checked 15.10.2026ADC2 may give wrong results
Size: per the Seeed KiCad footprint (21×17.8 mm).
FAQ
- Which Seeed XIAO ESP32C3 pins are I2C, SPI and UART?
- By default in arduino-esp32 (XIAO_ESP32C3): I2C: SDA GPIO6, SCL GPIO7; SPI: MOSI GPIO10, MISO GPIO9, SCK GPIO8, SS GPIO20; UART: TX GPIO21, RX GPIO20.
- Are the Seeed XIAO ESP32C3 pins 5 V tolerant?
- No. The logic is 3.3 V and the pins are not 5 V tolerant: use a divider or a level shifter for 5 V signals.
- Does ADC2 on the Seeed XIAO ESP32C3 work with Wi-Fi on?
- No. ADC2 pins (GPIO5) can't read analog while Wi-Fi is on. With Wi-Fi, use GPIO2-4 for the ADC.
You might also need
Similar boards
Next
- Emotion keychainmy ESP32-C3 project, prototype
- ESP32 music playermy ESP32 project, prototype
- DITHR//CAMmy ESP32 project, prototype
Need firmware or a device built on ESP32? I'll build it to order



