ESP32-S3-DevKitM-1 pinout
ESP32-S3-DevKitM-1, ESP32-S3, 3.3 V logic, 25.4×62.74 mm, 44 pins
verified20.10.2026
- 3V33.3 V
- 0GPIO0BOOTbuttonRTC_GPIO0
- 1GPIO1ADC1_CH0TOUCH1RTC_GPIO1
- 2GPIO2ADC1_CH1TOUCH2RTC_GPIO2
- 3GPIO3BOOTADC1_CH2TOUCH3RTC_GPIO3
- 4GPIO4ADC1_CH3TOUCH4RTC_GPIO4
- 5GPIO5ADC1_CH4TOUCH5RTC_GPIO5
- 6GPIO6ADC1_CH5TOUCH6RTC_GPIO6
- 7GPIO7ADC1_CH6TOUCH7RTC_GPIO7
- 8GPIO8I2C SDASUBSPICS1ADC1_CH7TOUCH8RTC_GPIO8
- 9GPIO9I2C SCLFSPIHDADC1_CH8TOUCH9RTC_GPIO9
- 10GPIO10FSPI CS0ADC1_CH9TOUCH10RTC_GPIO10
- 11GPIO11FSPI DADC2_CH0TOUCH11RTC_GPIO11
- 12GPIO12FSPI CLKADC2_CH1TOUCH12RTC_GPIO12
- 13GPIO13FSPI QADC2_CH2TOUCH13RTC_GPIO13
- 14GPIO14FSPIWPADC2_CH3TOUCH14RTC_GPIO14
- 15GPIO15U0RTSADC2_CH4RTC_GPIO15XTAL_32K_P
- 16GPIO16U0CTSADC2_CH5RTC_GPIO16XTAL_32K_N
- 17GPIO17U1TXDADC2_CH6RTC_GPIO17
- 18GPIO18U1RXDADC2_CH7RTC_GPIO18CLK_OUT3
- 5V5 V
- G
- G
- RSTbuttonCHIP_PU
- 46GPIO46BOOT
- 45GPIO45BOOT
- RXGPIO44UART0 RX
- TXGPIO43BOOTUART0 TX
- 42GPIO42JTAG MTMS
- 41GPIO41JTAG MTDI
- 40GPIO40JTAG MTDO
- 39GPIO39JTAG MTCK
- 38GPIO38FSPIWP
- 37GPIO37SPIDQS
- 36GPIO36SPIIO7
- 35GPIO35SPIIO6
- 34GPIO34SPIIO5FSPICS0
- 33GPIO33SPIIO4FSPIHD
- 26GPIO26SPICS1
- 21GPIO21RTC_GPIO21
- 20GPIO20USBU1CTSUSB D+ADC2_CH9RTC_GPIO20
- 19GPIO19USBU1RTSUSB D−ADC2_CH8RTC_GPIO19
- 48GPIO48LEDSPICLK_N
- 47GPIO47SPICLK_P
Top view, two USB ports at the bottom, module antenna at the top.
CompareDownload PNG- Chip
- ESP32-S3, ESP32-S3-MINI-1 or -1U (ESP32-S3FN8, 8 MB flash inside the chip package)
- Logic
- 3.3 V
- Power
- Micro-USB «UART» (CP2102N) 4.75-5.25 VMicro-USB "USB" (ESP32-S3 built-in USB) 4.75-5.25 V5V 4.75-5.25 V3V3 3-3.6 V
- Defaults in arduino-esp32 (ESP32S3 Dev Module)
- I2C: SDA 8, SCL 9SPI: MOSI 11, MISO 13, SCK 12, SS 10UART: TX 43, RX 44
Which ESP32-S3-DevKitM-1 pins are safe to use
Free to use
GPIO1, GPIO2, GPIO4-18, GPIO21, GPIO26, GPIO33-42, GPIO44, GPIO47
Use with care
- GPIO0, GPIO3, GPIO45, GPIO46: strapping: the level at power-up selects the boot mode.
- GPIO19, GPIO20: USB lines: use them and you lose USB flashing and the serial port.
- GPIO43: signal at boot.
- GPIO48: onboard LED.
Important
- 3.3 V logic, don't put 5 V on the GPIO.
- The board is discontinued (EOL). Espressif offers the ESP32-S3-DevKitC-1-N8R8 instead, the MINI-1 modules are still in production.
- ESP32-S3-MINI-1 module: ESP32-S3FN8 chip with 8 MB flash in the package, no PSRAM. GPIO26 and GPIO33-37 are free on this board.
- Strapping: GPIO0 (Boot button), 3, 45, 46. Keep GPIO45 and 46 low at power-up.
- ADC: ADC1 on GPIO1-10, ADC2 on GPIO11-20 (ADC2 may not work with Wi-Fi).
- The "USB" port is the chip's built-in USB on GPIO19/20. If you use these pins, the port stops working.
- Top pin: 1.40 mm from the edge by the drawing dimensions, 1.58 mm by the drawing geometry.
- Small components are drawn approximately, pins, module and board follow the dimension drawing.
- Per the manual the three power options are mutually exclusive: USB (one or both ports), 5V and G, 3V3 and G.
Revisions and clones
- Variant with the ESP32-S3-MINI-1U module: external antenna connector instead of the PCB antenna, same pins.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| 3V3 | 3.3 V | power inputpower output | verified | |
| 0 | GPIO0 | interruptPWM (LEDC)RTC_GPIO0 | not 5 V tolerantaffects boot (strapping)onboard button | verifiedAt reset: low = firmware download mode (BOOT button).Boot button on the board. |
| 1 | GPIO1 | interruptPWM (LEDC)ADC1_CH0TOUCH1RTC_GPIO1 | not 5 V tolerant | verified |
| 2 | GPIO2 | interruptPWM (LEDC)ADC1_CH1TOUCH2RTC_GPIO2 | not 5 V tolerant | verified |
| 3 | GPIO3 | interruptPWM (LEDC)ADC1_CH2TOUCH3RTC_GPIO3 | not 5 V tolerantaffects boot (strapping) | verifiedStrapping: JTAG signal source selection. Floating by default, no effect unless the eFuse was changed. |
| 4 | GPIO4 | interruptPWM (LEDC)ADC1_CH3TOUCH4RTC_GPIO4 | not 5 V tolerant | verified |
| 5 | GPIO5 | interruptPWM (LEDC)ADC1_CH4TOUCH5RTC_GPIO5 | not 5 V tolerant | verified |
| 6 | GPIO6 | interruptPWM (LEDC)ADC1_CH5TOUCH6RTC_GPIO6 | not 5 V tolerant | verified |
| 7 | GPIO7 | interruptPWM (LEDC)ADC1_CH6TOUCH7RTC_GPIO7 | not 5 V tolerant | verified |
| 8 | GPIO8 | interruptPWM (LEDC)ADC1_CH7TOUCH8RTC_GPIO8I2C SDASUBSPICS1 | not 5 V tolerant | verified |
| 9 | GPIO9 | interruptPWM (LEDC)ADC1_CH8TOUCH9RTC_GPIO9I2C SCLFSPIHD | not 5 V tolerant | verified |
| 10 | GPIO10 | interruptPWM (LEDC)ADC1_CH9TOUCH10RTC_GPIO10FSPI CS0 (SS) | not 5 V tolerant | verified |
| 11 | GPIO11 | interruptPWM (LEDC)ADC2_CH0TOUCH11RTC_GPIO11FSPI D (MOSI) | not 5 V tolerantADC2 doesn't work with Wi-Fi on | verifiedADC2: with Wi-Fi on, reading may not work (arbitration with Wi-Fi). Use GPIO1–10 for ADC. |
| 12 | GPIO12 | interruptPWM (LEDC)ADC2_CH1TOUCH12RTC_GPIO12FSPI CLK (SCK) | not 5 V tolerantADC2 doesn't work with Wi-Fi on | verifiedADC2: with Wi-Fi on, reading may not work (arbitration with Wi-Fi). Use GPIO1–10 for ADC. |
| 13 | GPIO13 | interruptPWM (LEDC)ADC2_CH2TOUCH13RTC_GPIO13FSPI Q (MISO) | not 5 V tolerantADC2 doesn't work with Wi-Fi on | verifiedADC2: with Wi-Fi on, reading may not work (arbitration with Wi-Fi). Use GPIO1–10 for ADC. |
| 14 | GPIO14 | interruptPWM (LEDC)ADC2_CH3TOUCH14RTC_GPIO14FSPIWP | not 5 V tolerantADC2 doesn't work with Wi-Fi on | verifiedADC2: with Wi-Fi on, reading may not work (arbitration with Wi-Fi). Use GPIO1–10 for ADC. |
| 15 | GPIO15 | interruptPWM (LEDC)ADC2_CH4RTC_GPIO15XTAL_32K_PU0RTS | not 5 V tolerantADC2 doesn't work with Wi-Fi on | verifiedADC2: with Wi-Fi on, reading may not work (arbitration with Wi-Fi). Use GPIO1–10 for ADC. |
| 16 | GPIO16 | interruptPWM (LEDC)ADC2_CH5RTC_GPIO16XTAL_32K_NU0CTS | not 5 V tolerantADC2 doesn't work with Wi-Fi on | verifiedADC2: with Wi-Fi on, reading may not work (arbitration with Wi-Fi). Use GPIO1–10 for ADC. |
| 17 | GPIO17 | interruptPWM (LEDC)ADC2_CH6RTC_GPIO17U1TXD | not 5 V tolerantADC2 doesn't work with Wi-Fi on | verifiedADC2: with Wi-Fi on, reading may not work (arbitration with Wi-Fi). Use GPIO1–10 for ADC. |
| 18 | GPIO18 | interruptPWM (LEDC)ADC2_CH7RTC_GPIO18U1RXDCLK_OUT3 | not 5 V tolerantADC2 doesn't work with Wi-Fi on | verifiedADC2: with Wi-Fi on, reading may not work (arbitration with Wi-Fi). Use GPIO1–10 for ADC. |
| 5V | 5 V | power inputpower output | verified | |
| G | Ground | verified | ||
| G | Ground | verified | ||
| RST | CHIP_PU (EN): enable and reset (low = reset) | onboard pull-uponboard button | verifiedReset button on the board. | |
| 46 | GPIO46 | interruptPWM (LEDC) | not 5 V tolerantaffects boot (strapping) | verifiedStrapping: together with GPIO0 selects the boot mode. Internal pull-down, must be low when booting over UART. |
| 45 | GPIO45 | interruptPWM (LEDC) | not 5 V tolerantaffects boot (strapping) | verifiedStrapping: VDD_SPI voltage. Internal pull-down, do not pull high at reset. |
| RX | GPIO44 | interruptPWM (LEDC)UART0 RX | not 5 V tolerant | verifiedConnected to the CP2102N ("UART" port). |
| TX | GPIO43 | interruptPWM (LEDC)UART0 TX | not 5 V tolerantoutputs a signal at boot | verifiedConnected to the CP2102N ("UART" port). |
| 42 | GPIO42 | interruptPWM (LEDC)JTAG MTMS | not 5 V tolerant | verified |
| 41 | GPIO41 | interruptPWM (LEDC)JTAG MTDI | not 5 V tolerant | verified |
| 40 | GPIO40 | interruptPWM (LEDC)JTAG MTDO | not 5 V tolerant | verified |
| 39 | GPIO39 | interruptPWM (LEDC)JTAG MTCK | not 5 V tolerant | verified |
| 38 | GPIO38 | interruptPWM (LEDC)FSPIWP | not 5 V tolerant | verified |
| 37 | GPIO37 | interruptPWM (LEDC)SPIDQS (Octal) | not 5 V tolerant | verifiedOn the ESP32-S3-MINI-1 flash and PSRAM are quad (Quad SPI): the pin is free. |
| 36 | GPIO36 | interruptPWM (LEDC)SPIIO7 (Octal) | not 5 V tolerant | verifiedOn the ESP32-S3-MINI-1 flash and PSRAM are quad (Quad SPI): the pin is free. |
| 35 | GPIO35 | interruptPWM (LEDC)SPIIO6 (Octal) | not 5 V tolerant | verifiedOn the ESP32-S3-MINI-1 flash and PSRAM are quad (Quad SPI): the pin is free. |
| 34 | GPIO34 | interruptPWM (LEDC)SPIIO5FSPICS0 | not 5 V tolerant | verified |
| 33 | GPIO33 | interruptPWM (LEDC)SPIIO4FSPIHD | not 5 V tolerant | verified |
| 26 | GPIO26 | interruptPWM (LEDC)SPICS1 | not 5 V tolerant | verifiedOn ESP32-S3-MINI-1-N4R2 modules it is used by the built-in PSRAM. On the N8 module (ESP32-S3FN8 chip, on this board) it is free. |
| 21 | GPIO21 | interruptPWM (LEDC)RTC_GPIO21 | not 5 V tolerant | verified |
| 20 | GPIO20 | interruptPWM (LEDC)ADC2_CH9RTC_GPIO20USB D+U1CTS | not 5 V tolerantADC2 doesn't work with Wi-Fi onUSB line | verifiedADC2: with Wi-Fi on, reading may not work (arbitration with Wi-Fi). Use GPIO1–10 for ADC.Built-in USB lines (the USB port on the board). If you use them as GPIO, USB disappears.Connected to the board "USB" port (D+). |
| 19 | GPIO19 | interruptPWM (LEDC)ADC2_CH8RTC_GPIO19USB D−U1RTS | not 5 V tolerantADC2 doesn't work with Wi-Fi onUSB line | verifiedADC2: with Wi-Fi on, reading may not work (arbitration with Wi-Fi). Use GPIO1–10 for ADC.Built-in USB lines (the USB port on the board). If you use them as GPIO, USB disappears.Connected to the board "USB" port (D−). |
| 48 | GPIO48 | interruptPWM (LEDC)SPICLK_N | not 5 V tolerantonboard LED | verifiedAddressable RGB LED on the board, labeled "RGB@IO48". |
| 47 | GPIO47 | interruptPWM (LEDC)SPICLK_P | not 5 V tolerant | verified |
Sources
Every pin is verified against the manufacturer's documents.
- ESP32-S3-DevKitM-1 User Guide (Espressif), Header Block J1/J3user guide, checked 20.10.2026function of all 44 pins of J1 and J3, RGB LED on GPIO48, Boot and Reset buttons, two USB ports, three power options, board discontinued
- ESP32-S3-DevKitM-1 V1 dimensions (PDF, 2021-03-10)board drawing, checked 20.10.2026board 25.40×62.74 mm, rows 1.27 mm from the edges, 2.54 pitch, bottom pin 8.00 mm from the bottom edge, silkscreen labels, position of the module, buttons and USB
- ESP32-S3-DevKitM-1 V1 schematic (2021-03-10)schematic, checked 20.10.2026CP2102N-A02-GQFN28, SGM2212-3.3, SK68XXMINI-HS, red power LED
- ESP32-S3-MINI-1 & MINI-1U Datasheet v1.7 (Espressif)datasheet, checked 20.10.2026module pins: GPIO26 (SPICS1), GPIO33 (SPIIO4, FSPIHD), GPIO34 (SPIIO5, FSPICS0), GPIO35-37; on the -N4R2 GPIO26 is used by PSRAM; N8 and N4R2 with Quad SPI flash
- ESP32-S3 Series Datasheet (Espressif)datasheet, checked 15.10.2026pin functions: ADC1_CH0–9 on GPIO1–10, ADC2_CH0–9 on GPIO11–20, TOUCH1–14, RTC GPIO0–21, USB GPIO19/20, JTAG GPIO39–42, UART0 GPIO43/44, strapping GPIO0/3/45/46
- ESP-IDF: GPIO (ESP32-S3)user guide, checked 15.10.2026GPIO26–32 are used by SPI flash/PSRAM, GPIO33–37 are used on modules with Octal flash/PSRAM, strapping pins, USB
- arduino-esp32: variants/esp32s3/pins_arduino.hArduino core, checked 15.10.2026defaults: TX 43, RX 44, SDA 8, SCL 9, SS 10, MOSI 11, MISO 13, SCK 12
Size: from the Espressif V1 dimension drawing (2021-03-10); from the drawing geometry itself about 62.87.
FAQ
- Which ESP32-S3-DevKitM-1 pins are I2C, SPI and UART?
- By default in arduino-esp32 (ESP32S3 Dev Module): I2C: SDA GPIO8, SCL GPIO9; SPI: MOSI GPIO11, MISO GPIO13, SCK GPIO12, SS GPIO10; UART: TX GPIO43, RX GPIO44.
- Which pin is the ESP32-S3-DevKitM-1 LED on?
- SK68XXMINI-HS RGB LED on GPIO48.
- Are the ESP32-S3-DevKitM-1 pins 5 V tolerant?
- No. The logic is 3.3 V and the pins are not 5 V tolerant: use a divider or a level shifter for 5 V signals.
- Does ADC2 on the ESP32-S3-DevKitM-1 work with Wi-Fi on?
- No. ADC2 pins (GPIO11-20) can't read analog while Wi-Fi is on. With Wi-Fi, use GPIO1-10 for the ADC.
You might also need
Schematic with this board
schematic builder with the board already placed
Flash this board
upload a sketch or .bin to this board from the browser
Power budget
will the regulator cope and how long the battery lasts
Calculators
LED resistor, voltage divider, battery runtime, 3D print cost, LED strip power supply and pF, nF, µF conversion
Similar boards
Next
- Emotion keychainmy ESP32-S3 project, prototype
- Troll Botmy ESP32-S3 project, prototype
- olerast PULSEmy ESP32-S3 project, in development
Need firmware or a device built on ESP32? I'll build it to order



