1.44" 128×128 ST7735S display pinout
1.44" 128×128 ST7735S display, SPI (red board, 8 pins), Sitronix ST7735S, 3.3 V logic, 29.7×43.36 mm, 8 pins
partly verified17.10.2026
Front view (screen side), connector at the top.
BuyDownload PNG- Chip
- Sitronix ST7735S
- Logic
- 3.3 V
- Power
- VCC 3.3-5 V
Important
- SDA and SCK are SPI (MOSI and SCK), there is no MISO. A0 is D/C.
- 3.3-5 V supply, 3.3 V logic: with a 5 V Arduino you need dividers or a level shifter.
- Libraries: Adafruit_ST7735 (initR(INITR_144GREENTAB)), TFT_eSPI, LovyanGFX. Different batches can shift the image by 1-3 pixels.
- Board size per the module manufacturer; connector and glass position from the photo (±1 mm), not measured.
Revisions and clones
- The 1.8" 128×160 on the ST7735 looks similar, but has a card slot and a different pin order: it is a different module.
All pins
| Label | Number | Functions | Limits | Check |
|---|---|---|---|---|
| VCC | 5 V | power input | not from manufacturerOrder per LCDWIKI; unbranded red boards usually match, but check the silkscreen. Header position is not dimensioned. | |
| GND | Ground | not from manufacturerOrder per LCDWIKI; unbranded red boards usually match, but check the silkscreen. Header position is not dimensioned. | ||
| CS | SPI CS, active low | not 5 V tolerant | not from manufacturerOrder per LCDWIKI; unbranded red boards usually match, but check the silkscreen. Header position is not dimensioned. | |
| RESET | Reset, active low | not 5 V tolerant | not from manufacturerOrder per LCDWIKI; unbranded red boards usually match, but check the silkscreen. Header position is not dimensioned.Labelled on other revisions as: RES, RST | |
| A0 | D/C: low = command, high = data | not 5 V tolerant | not from manufacturerOrder per LCDWIKI; unbranded red boards usually match, but check the silkscreen. Header position is not dimensioned.LCDWIKI's table says the opposite; per the ST7735S datasheet a low D/CX level means a command.Labelled on other revisions as: DC, RS | |
| SDA | SPI MOSI (labeled SDA on the board) | not 5 V tolerant | not from manufacturerOrder per LCDWIKI; unbranded red boards usually match, but check the silkscreen. Header position is not dimensioned.This is SPI, not I2C. | |
| SCK | SPI SCK | not 5 V tolerant | not from manufacturerOrder per LCDWIKI; unbranded red boards usually match, but check the silkscreen. Header position is not dimensioned. | |
| LED | Backlight: high is on | not 5 V tolerant | not from manufacturerOrder per LCDWIKI; unbranded red boards usually match, but check the silkscreen. Header position is not dimensioned.If you do not control it, connect to 3.3 V.Labelled on other revisions as: BL, BLK |
Sources
Not verified against the manufacturer: 8 of 8 pins. The pin card says what confirms each one and where sources disagree.
- LCDWIKI: 1.44inch SPI Module ST7735S SKU:MSP1443user guide, checked 17.10.2026order VCC, GND, CS, RESET, A0, SDA, SCK, LED; 3.3-5 V supply, 3.3 V logic; board 29.7×43.36; active area 26.2×27.2
- LCDWIKI: MSP1443 User Manual (PDF)user guide, checked 17.10.2026manual for the same module
- Sitronix ST7735S datasheet (rhydolabz copy)datasheet, checked 17.10.2026SPI: SCL, SDA, CSX, D/CX (low is a command), RESX
Size: 29.7×43.36 per LCDWIKI (approximate).
FAQ
- What supply voltage does the 1.44" 128×128 ST7735S display need?
- VCC: 3.3-5 V. 3.3 V logic.



